KSCS25FV KitchenAid Refrigerator - Instructions

Easy as pie, I followed the directions on the box that the replacement filter came in, and installed it and the cap simply and easily.

This was a pretty easy repair...I removed the retaining screws and slid the assembly off its tracks. Disconneting the wiring hardness was a pain but after a few minutes I had that off (use gloves, it gets cold in the freezer after a minute)

Once I had the unit completely out of the freezer the replacement part took only minutes ... Read more to replace.

Reversed the process putting the ice maker back in - a few hours later my ice buck was full again.

Simple repair - well worth the effort.

Turn off water supply too ice maker and unplug the fridge power. using a nut driver remove one bottom screw from the bottom, near the front. The other two from the side atop the ice mold. (loosen screws and ice maker will lift up and off.)
I set the ice maker on the counter, snapped of the front cover by hand. using a phillips d ... Read more river, remove two screws near the bottom corners.(they go through the circuit board into the ice mold)
circuit board in one hand, other end of ice mold in the other, slowly pull apart about 1 inch. remove the silver colored "on, off" bar at the end by snapping the retainer out of the ice mold. (the silver bar stays with the circuit board end)
Watch how the ice guide(white fingers stationary on side of ice mold) hooks too the ice mold on each end. swap ice guide to new ice mold, insert three guide pins on end into holes on the circuit board, while holding ice guide onto ice mold, watch rotation bar while inserting into motor.(it only splines one way.) when each piece is lined up, simply push together and reinstall two screws. snap circuit board cover into place. reinstall ice maker into freezer in reverse order.

Ice Maker quit working. Seemed like a water supply issue but when I read the other reviews, I decided to install and see. bolted the bracket on with three screws, slid in place. Nothing happened and about 10 minutes later, I heard the water release to the ise maker and have been making ice ever since.

tested bulb good ,replaced door switch first(least expensive)then ordered light socket and circuitboard.If clicking sound is heard replace circuitboard first to save on return shipping because the switch and socket where ok

Removed the three motor screws pulled off old motor put new motor in place replaced screws and re-installed. It was producing ice three hours later. I originally tried to obtian these parts directly from Whirlpool in which twice they shipped me the wrong parts. Finally gave up on them and entered the whilrpool part number which crossref ... Read more erenced to new part number which was correct the first try. Thank you!

First I unplugged the unit, then I popped off the cover to the icemaker electronics. Removed 4 screws, pulled out the broken electronic panel, and replaced with the new one. Returned the screws and cover. The next moring the ice bin was full.

This must have saved me $300, and the inconvernience of waiting around for the repai ... Read more r man. He would have made two trips since he would never have had this part with him.

applied clear plastic packing tape on the inside of the bins to re-enforce the poor construction and hopefully add life to the part. Remove the old part and replaced with fortified part by slipping into place.

Removed 3 screws on the bottom of old ice maker in the fridge, slid out old ice maker, disconnected electrical cable,took out old ice maker. Take the plastic tray from bottom of old ice maker install on new ice maker, reconnect cable, slid in place, replace the three screws. About 3 hours later water ran in and new ice maker started to ma ... Read more ke ice. The only thing I missed was I didn't rinse out new ice maker before installation. If you don't rinse out new ice maker you have to throw away the first full bin of ice due to metallic taste.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First removed one screw from the bottom right bottom side of the unit. Removed the door from the front of the unit. Pushed up the locking tab on the left underside of the unit and pulled the unit partway out. Removed the plastic cover ( that was retained by the screw removed and disconnected the electrical connection) and finished removin ... Read more g the unit from the freezer. Removed the remaining three screws from the bottom of the unit and installed on the bottom of the new unit. I then slid the new unit partially in and connected the wiring harness and slid the rest of the way in guiding the water line into thepocket which was taller than the origional unit. Reinstalled the wire protective cover with one screw and the front cover back on the new unit. Done and is working great.

We took out the old filter and put in the new one. Ran out a few gallons of water then it was ready to use.

first i put in a new water inlet valve it did not solve the problem i waited 3 days then ordered the ice maker i put it in an it still did not work after 3 days i put in water in the ice maker by hand it still did not work i gave up then to my surprise 4 more days it started working still not sure what was wrong but i am glad it works now ... Read more this was about a two week process one tip on getting ice maker out is to take the door that's covers ice maker off no tools needed then remove three screws slip it in an out there is a helpful video for water inlet thank you mike b

We had electrical storm and lost power. When it returned the cable box and the Frig display didn't come back on.
I disassembled the Frig door panel to view the assembly. With an educated guess I ordered the control board. It took approx 10 minutes to install. It works as it should.

Heating element broke and fried the rest of the parts had to take out the bad parts and put in the new ones and it worked. i have fixed this problem three times now.