KHWS02RMT2 KitchenAid Washer - Instructions

Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately ... Read more $150.00 bucks in repair service fees.

Pretty easy part replacing job. All screws were torx. Pry off plastic molding from front of machine where it covers the hinge with an old thin table knife or something, loosen the plastic molding inside the door, and replace the hinge. Minor hint... put the little round plastic molding back on the round part of the hinge BEFORE you scr ... Read more ew the hinge onto the door.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

baffle just clicked into place by aligining tabs on baffle with openings on drum. very easy.

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a ... Read more couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Everything went great from order to done. Very happy

The best way to do it is not the way I started.
The best way is to 1st remove the bellow's front clamp with a small screwdriver at the spring. 2. unplug the 3 sets of wires attached to the lock. 3. remove the 3 screws on the front that hold the lock. 4. remove the plastic ribbon harness that attaches to the lock. 5. remove the old l ... Read more ock. 6. install the lock back carefully moving aside the cables. 7. install the 3 screws. 8. attach the ribbon harness. 9. attach the cables. 10. replace the bellow. 10. replace the clamp (here you may need someone's help to keep the rubber in place.) 11. the last part to fall in place is where the spring is. 12. If you can't do all by tact then you may want to remove the 3 screws from the top cover to be able to c where all fits.

Remove three screws holding the lower panel, the pump is right up front. Probably the hardest part was holding the hose clamps open while attaching the hoses to the pump housing. One screw holds the pump assembly in place. Hold the over-ride switch closed, check for leaks, and replace the loser panel.

Turned off the water and unplugged the machine

Took off the top of the washing machine by removing three screws along the back side

Removed the hoses connected to the water inlet valve

Removed the hose coming out of the water inlet valve

Marked the 4 electrical connectors

Used plyers ... Read more to pull the electrical connectors off. Needed to just pull hard. Won't break them off.

Remove the screw that connects the valve to the back of the appliance.

I confirmed this was the part causing the problem by blowing air through it with my mouth. I could tell that the hot water side was not closing all the way.

To replace the part, just repeat the steps above in reverse.

This part slides in and snaps in place, a 15 second job.

removed all the panels to change the door latch switch
plug in three plugs ...works great
Thank you

Was able to remove old bellow without dis-assembly. Replacement required removing the front of the machine for access. Once the front was off, the bellow was simple to replace. Biggest difficulty is getting the top mark on the bellow lined up. It has a tendency to slip out of position while you are working the back of the bellow over th ... Read more e retaining lip and it is not possible to rotate the bellow after it is installed. Fortunately, the tube from the detergent tray can be rotated slightly to allow for a small amount of error. Replacing the front retaining wire and spring required three hands at one point, but was otherwise not a problem. Fortunately removal and replacement of the front of the machine is pretty straight forward. I needed to disconnect wires to set the front out of the way, but it is impossible to plug them back in incorrectly.

Just removed the bottom cover to access the water pump. Drained the water through the filter housing. One screw and two hose clamps and the pump was out. Installed new pump and checked for leaks. None found so the cover was secured in plase. Great news, WIFE is happy.