KHWS0 KitchenAid Washer - Instructions

This washer had been faulting since it was 1 year old but it only happened 1 to 2 times a year. As the fault problem became more often, I realized it was a hardware or computer malfunction. But what was the problem? Well the problem always was a faulty flow meter. I replace the valve and the flow meter. But I tested the flow meter several ... Read more times.-- I replaced the flow meter and the valve. And for once in 5 years it did not fault.

I wasted 2 years washing clothes in mu Duet before I repaired it in just two minutes. In those 2 years we destroyed numerous articles of clothing because the missing baffle left sharp metal corners that cut holes in to so many of our clothes. The replacement baffle was easy to find on partselect.com as were installation guides. I can' ... Read more t believe how easy it was!

Serviceman had previously replaced the hot and cold inlet valves, but the low pressure error persisted. Rather than cough up another $130 for the serviceman to return, plus parts and time, I decided to order the replacement flowmeter from PartSelect.

Unplug power and turn off water. Top of machine comes off by removing three sc ... Read more rews at top rear; use socket, spanner or T20 driver. Unplug electric sensor from flowmeter. Old unit is removed, and new one connected to water line by squeezing spring-clips with a pair of flat nose pliers. Reconnect electric sensor.

Great move, easy, and saved myself the thick end of $200.

I romoved the front of the washer access panel. I then used the pliers to remove the clamps from the old hose and to replaceit with the new one.

The repair was rather easy. It involved the removal of all the bolts around the glass door and only the bolts on the hinge conected to the washer itself. there was a bit of alignment problem when put back together, minor rubbing, but not much. The door now works close to as good as new.

First step was to remove old bellow. I opened the door there is a small wire with a spring attach that holds the outside of the bellow to thw washer. Then removed it from the water inlet, then took a short straight scewdriver to remove the gaint hose clamp holding it to the drum. Installed the new part. When putting hose clamp back on I r ... Read more emoved the top of the washer by removing the three screws in the back then I flipped the hose clamp so I could use a long screwdiver from the top side.This will give you alot more room. Hope this helps

Removed three mounting screws to the front access panel, removed panel, cleaned out drain trap, attempted to reset and drain washer, pump did not operate. Removed one wire harness to pump, two hose clamps and slipped pump assembly out of its mounting grommets, and installed new pump in reverse order. A sinch! And saved me approximately ... Read more $150.00 bucks in repair service fees.

slid new baffle into place. No directions with new part, fortunately it was easy to figure out how baffle locked into place.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

First and foremost, I usually call a real man to come do a job like this, but after reading the repair stories, I gave it a shot. Very, very easy. Pop of the bottom panel off (three torx screws), drain the water out of the tub (if any), and just follow the directions in the box. Anyone can do this one.

Pretty easy part replacing job. All screws were torx. Pry off plastic molding from front of machine where it covers the hinge with an old thin table knife or something, loosen the plastic molding inside the door, and replace the hinge. Minor hint... put the little round plastic molding back on the round part of the hinge BEFORE you scr ... Read more ew the hinge onto the door.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

baffle just clicked into place by aligining tabs on baffle with openings on drum. very easy.

Brother who used to sell appliances opened the washer door and read the booklet inside the washer telling him the part necessary to repair the problem. $33/00 for the water flow meter Part and shipped in next morning and arrived overnight. Excellent service for only $7.00 shipping. Highly recommend this place for parts. This was after a ... Read more couple of days searching the internet for those with the same problem and not receiving and exact part to fix the problem

Everything went great from order to done. Very happy