KHWS0 KitchenAid Washer - Instructions

While looking at the new baffle it became evedent that I would need to remove the top of the unit to secure the new baffle to the drum. This was easly done by removing the top of the unit. I removed the three screws from the top back of the unit. Once the top was off I located the inlet tube for the detergent to the drum. I was able to sp ... Read more in the drum and locate the underside of the baffle by looking through the hole where the tube had been attached . I then installed the baffle and snapped it in place. I turned the drum to locate the hole again and installed the screw that was supplied with the new baffle. I then returned the tube back to the location it had orginally been installed. I returned the top and reinstalled the screws to the back of the unit. Whrilpool wanted to replace the entire drum at a cost of $480.00 for the part alone. This is much more cost effective with just a small bit of work. I have contacted Whrilpool for the part number and they would only tell me that I needed a whole drum. I was contacted by a rep from Whrilpool and she told me that I was wrong I could not have done this without replacing the whole drum. My wife will tell all who ask that this unit is working wonderfully.

Opened the front panel with 3 crews T-25 or socket wrench. Panel comes off right away.

Look for the leak. Determined it was the hose. Use power pliers to remove the clamp.

The small clamp was easy. The big one I had to use my yoga to get to it. It probably would had been easy from the back panel but moving the machi ... Read more ne requires brute force.

Once the hose was out I found some bra under wires which is what probably punctured the hose.

Removed the front filter and found a bunch of nails.

Assembly was much easier and placed clamps so that if needed it would be a lot easier to remove and replace.

Removed bellow clamp (used screwdriver to pry clamp open). Removed Bellow to Outer Tub Clamp with socket set. Removed Bellow. I had purchased new clamps as I didn't know condition of the old clamps. The Bellow to Outer Tub Clamp was in good condition, appeared to have an anodized finish - was not corroded and the tightening screw point ... Read more ed forward where as the new clamp appeared to be galvanized and the tightening screw paralled the clamp. I assumed the new orientation of the tightening screw was to make it easier to tighten with a screwdriver, but space is limited and I had good success removing the old clamp with a socket set so I elected to reuse the old clamp. Plus, I liked the finish of the old clamp better - it had zero corrosion on it after several years, almost a decade, of use.
Reinstalling the bellow was the hardest part of the repair - it is just tedious and patience is required - I took a couple of breaks seating the Bellow to the outer tub. There was a tab on the Bellow which went to the top to insure the Bellow was properly aligned. After I seated the bead of the Bellow all the way around, I slipped the Bellow to Outer Tub Clamp over the Bellow and tightened it down - continually checking the seating of the Bellow. I then put the Bellow over the water inlet tube and seated the outer portion of the Bellow. I needed additional hands to help hold the outer clamp in place - my wife helped - and I used pliers and plastic pry wedges from a tire patch repair kit to pull it open and slip it over the Bellow - I didn't want to use screwdrives as I was afraid I would damage the Bellow.

Turn off both hot an cold water supply valves. Unscrew both hot and cold supply hoses from rear of washer making note of which inlet they came off of. Pull washer out to access screws to remove top cover and water inlet valve. Remove top cover unscrewing 3 torx screws on the rear of the washer. Unplug the 4 wires wires from water inlet va ... Read more lve - make sure you remember which pairs go to which solenoid. Remove 1 phillips head screw that secures the water inlet valve to the back of the washer. Remove water inlet valve. With a pair of pliers loosen the hose clamp and remove the hose from the inlet valve. Take the new water inlet valve and loosen hose clamp with pliers and push the hose onto the barbed fitting as far as it will go. Make sure hose clamp is over barbed fitting securing the hose. Attach both pairs of wires to the solenoids in the same position that you removed them. Position water inlet valve into place and secure with phillips screw. The part that I received did not quite line up with the hole on the rear of my washer so I had to elongate the existing hole on the rear of the washer with a drill so I could secure the water inlet valve as designed. Screw on both water supply lines making sure the hot and cold are screwed back on to the right inlets. Turn both water supply valves on and test looking for leaks. Secure the top cover back on with the 3 torx screws and push washer back into place. Viola! Ready for the next load of wash.

Ran diagnostics for this model (you can look for its service manual on the web which details how to do this). The diagnostics said the cold water inlet valve or the flow-meter were broken. To pin the issue down to one component, I switched the cold/hot water control cables going into the inlet valve assembly and switched the cold/hot wat ... Read more er hoses. Ran diagnostics again and the cold water and flow meter passed but got a failure on the hot water inlet valve. This pointed to a bad cold-water inlet valve. I ordered a replacement at PartsSelect. Installation took less than ten minutes. Machine runs like a dream. Before all this I called a service center, and without even looking at the machine, they quoted no less than $300. But with a little reading and some sleuth work, I ended up paying only $70 for the part + S/H.

Like most folks, my daughter has tossed the shipping bolts after her puechase, I moved her the first time w/o any thought to it but commercial movers won't do that, they will chg. you to have it done and it's not cheap, akin to an appliance repair. This kit contains all four bolts/spacers, (2) upper and (2) lower. Hard to tell from the de ... Read more cription but a sweet gal on the help desk assured me of it. Got it fast and got them installed in minutes, easy to do and wrote a big note on the back of the washer to save them!! No idea why your owners book says "do not reuse".

1st I removed the front retaining ring. You do need to get down near the ground to see the retaining ring. I used two pairs of needle nosed pliers to pull the ring apart (which has a spring in the middle) and then removed the ring.

Then I pushed the bellows into the washing machine drum, pulled the water inlet valve from the be ... Read more llows, and used a short flat blade screwdriver to remove the retaining band (upper right of the bellows) After doing this it was a simple matter to remove the whole unit.

I did find it was easier to remove the washing machine door.

The installation was a simple matter of reversing the above. I had no problems with this repair. I would STRONGLY suggest, unless you are one of those gifted 3 handed people, getting an assistant to push the outer retaining ring into place as you separate the spring.

Simple, easy repair.

The Part Select website has some great information provided by customers. I search my error code problem that shut down the washer when filling and found the most likely scenario was a faulty flowmeter.
The other problem happening at the same time was the drum filling with water when the appliance was not in use. I thought the two ... Read more problems were related, but upon further research decided that the most likely cause was a faulty water inlet valve.
I order the parts from Part Select and I could not believe how fast the shipping was. I just ordered regular ground but the parts got here in a couple of days.
The repair was easy. Remove four screws (need a star bit) from the top lid of the washer and remove the cover. The flowmeter and the water inlet valve sit right on top of the washer. Even with the lousy set of pliers I used, removing the clamps and disconnecting the hoses on both parts was easy off and easy back on. I had more trouble with the electrical leads on the water inlet, only because they were on so securely and I didn't want to rip out the wiring.
All together the repair for both parts took about 30 minutes.
Make sure you turn off the water supply and be ready to mop up a little excess water from the water supply lines when you disconnect them from the washer's water inlet valve.

We had to bread the hinge that had rusted out. That was the worst part. Putting the new hinge was no big deal. The time factor was also great. I called on Monday and had the part by Thursay. With a family of 6 a washer is a huge necessity.

Had to take the entire front of the washer off to replace the door latch.

I found a you tube video with step by step instructions. Very easy to follow. Repair would have been quicker had my kids not been at home. I had to have my boyfriend help me put on the outer bellow spring clamp, as I was not strong enough. Washer works great.

Remove the lower front cover there are three small torx type screw. The pump is the very first thing you see. Have a wet and dry Vac available you will need it. The drain pump and the drain lines contain a lot of water. Unscrew the big white drain plug at the pump and clean up the water, remove the front small mounting screw and disconnec ... Read more t the two hoses in the back of the pump with pliers and follow the pre-printed steps in reverse. If your machine is more than six years old you will have to use a utility knife and remove a piece of plastic on the electrical connector that is from the washer wiring, if you force the connection on it will brake, look at the connection and the plug and attempt to plug it in before you install the pump. It is easy just be-aware of the connector.

Removed back panel,unscrewed the nut on the pulley.Removed pulley and belt. Reassembled.

Peel rubber gasket from drum; remove 3 screws using phillip head screwdriver; disconnect wiring e plugs; remove door lock. Install in reverse order.

removed screws on front control panel. found info sheet. read that this part was correct. replaced the motor control unit tho saw no damage on old unit and it works fine now.