My Orders
- Home
- KHMS2050SSS0
- Instructions
KHMS2050SSS0 KitchenAid Microwave - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replaced door handle with worn off silver finish.
2 of 2 people
found this instruction helpful.
-
Dan from TUMWATER, WA
- Easy
- 15 - 30 mins
-
Screw drivers
Unscrewed 3 screws on side of door and two on the bottom. Slowly pry apart outside frame from black inside facing door. Separate pieces carefully. You won’t have to completely remove outside door cover if you have a short driver for the two Torx screws holding the handle on. Replace and carefully put back together. Tip: do not oversc
... Read more
rew the screws, back in, it will easily crack the old plastic.
Read less
Was this helpful?
Thank you for voting!
Loud noise
1 person
found this instruction helpful.
-
Cynthia from DRIPPING SPGS, TX
- Really Easy
- 15 - 30 mins
-
Screw drivers
Changed out turntable motor
Was this helpful?
Thank you for voting!
my pan that browns the meat started to bubble and peal
1 person
found this instruction helpful.
-
Lillian from SAN JOSE, CA
- Really Easy
- Less than 15 mins
I really did not have a repair on the microwave just a replacement of the browning pan
Was this helpful?
Thank you for voting!
Lost spring that holds filter in hood that was lost when cleaning it.
1 of 2 people
found this instruction helpful.
-
Raymond from Mechanicsville, VA
- Really Easy
- Less than 15 mins
simply removed the filter casing from the microwave, then removed both filters and inserted the spring after bending it slightly.
Was this helpful?
Thank you for voting!
lost the driver
1 of 2 people
found this instruction helpful.
-
Luiz from Washington, DC
- Very Easy
- Less than 15 mins
just insert it in the right side
Was this helpful?
Thank you for voting!
machine was dead.
3 of 8 people
found this instruction helpful.
-
Mark from Smithtown, NY
- A Bit Difficult
- 1- 2 hours
-
Pliers, Screw drivers
After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "P
... Read more
art Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)
Read less
Was this helpful?
Thank you for voting!
Microwave had no electrical
1 of 5 people
found this instruction helpful.
-
Larry from HARKER HTS, TX
- Really Easy
- 30 - 60 mins
-
Pliers
I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.
Was this helpful?
Thank you for voting!
Broken microwave door handle
1 of 5 people
found this instruction helpful.
-
jody from HENDERSONVLLE, NC
- Easy
- Less than 15 mins
Oprnef the door frame and took off old handle
Was this helpful?
Thank you for voting!
it was working fine and it stopped order a fuse and it wasn't the problem
0 of 4 people
found this instruction helpful.
-
Herb from Auburn, IN
- A Bit Difficult
- 1- 2 hours
took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse
Was this helpful?
Thank you for voting!
The door of my whirlpool microwave broke off
5 of 20 people
found this instruction helpful.
-
Pete from Kensington, MD
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I purchased the door handle to model KHMS1850SWH0 for around $50; the model I have,KHMS1850SWH1, only offers the entire door as a replacement for over $200. The earlier model door handle fit great with no problems.
Was this helpful?
Thank you for voting!
Put the Fuse in, then plugged it in came on for a min then everything went out!!!!!
4 of 18 people
found this instruction helpful.
-
Stephen from SPRINGFIELD, WV
- Very Difficult
- 1- 2 hours
-
Pliers, Screw drivers
Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!
Was this helpful?
Thank you for voting!
light bulbs nedd to repace it.
45 of 196 people
found this instruction helpful.
-
Jorge from Bay Point, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took the the want burned out , and put the new ones.
Was this helpful?
Thank you for voting!
Light Burned Out
-
Patti from Coarsegold, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Followed the instruction booklet that came with the microwave. Very easy.
Was this helpful?
Thank you for voting!
Replace charcoal filter
-
Louise from Mason, OH
- Really Easy
- Less than 15 mins
Took old one out,and clipped new one in.
Was this helpful?
Thank you for voting!
Dirty filters
-
Anna from Antioch, CA
- Really Easy
- Less than 15 mins
Removed the dirty ones and put in the new ones. This was really not a repair. No tools needed.
Was this helpful?
Thank you for voting!