KHMS204 - Instructions

Took out turntable and swapped out old one with a new bright and shiny
New one, ring that is. It was easy using the part from parts select
Thanks
Paul

It was a very simple and easy fix, no tools needed. First, open the door to the microwave/oven and remove the glass plate and the plastic plate guide. Next, locate the whole in the center. Using your finger, find the drive coupling pin that sits just below the opening (half circle shape). Align the bottom of the drive coupling with the me ... Read more tal pin and press down. Replace the plate guide and plate. The grooves in the bottom of the glass plate should be aligned with the shape of the drive coupling. Test by setting microwave/oven to 30 seconds and watch for proper turning and alignment.

First, we had to clean up all the interior surfaces, which was just cleaning. There was no internal damage. Then, just setting the center connector, rotary rollers and glass plate. Simple

removed perimeter screws from the bottom side and the lower cover is hinged at the wall side. Motor is visible and easily removed with two screws. Take of the old one, install the new one, and reverse the procedure to put the bottom cover back in place. Will nee helper to hold one side of the bottom until couple of screws can be put in on ... Read more the other side.

Based on other similar posted repairs, I purchased the bottom switch. Upon removing the control panel to replace the switch, I found the blue 22 gauge wire was broken at the spade terminal. This wire had been crimped to the terminal along with a 14 gauge wire. Apparently the force to crimp the thicker wire weakened the smaller wire at ... Read more the terminal. I stripped the end of the small blue wire and reattached it to the thicker wire using a solder iron and solder. The repair fixed the problem.

It took me 15 minutes total - 5 minutes to clean the microwave, 1 minute to install three new parts, and 9 minutes to enjoy my celebratory glass of wine!

Took out the turntable parts to ensure I ordered the correct cooking tray. Matching those with photos of related parts on PartSelect worked great. Put turntable drive and support ring in place and cooking tray went in very easily. Plan to order a second one to have on hand for this rental property.

Ordered the glass tray and installed it. Received the orderin about two days.

Ordered a new motor. Removed the outside trim of the oven-microwave combo. 2 screws at the bottom of the trim. Removed the screws that held the combination micro and oven unit in place. Removed the top and bottom black plastic grill of the microwave. 3 screws each. Pulled the entire unit out about 1 inch exposing the screws at each ... Read more side of the microwave that hold it in place.
Snapped off the top control panel which exposed the wiring connecting the control panel.
Unplugged a couple of wire harness units to free the control panel.
Be sure to label the units to know which goes where during reassembly.
Remove the microwave unit from the housing and place it on its side.
Remove the metal plate that houses the motor. 4 screws hold the motor in place. Disconnect the 2 wires from the old motor and you are ready to install the new motor. Be sure to TURN OFF THE POWER to the unit at the breaker box and remove the turntable from inside the microwave.

I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.

Once the part arrived, install was simple, lining up the existing holes. The only hard p ... Read more art was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.

Overall a very simple repair.

On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.

Unscrewed glass panel, removed old bulb, cleaned glass panel and installed new bulb. Screwed panel back into place.

I took off the glass panel underneath the microwave and replaced the 2 bulbs in less than 3 minutes by myself with only a phillips head screwdriver. I was very pleased with the service I received and more pleased with myself that I did not have to call in a repair man.

Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.

replaced with new one