Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My dryer wasn't getting hot.
0 of 1 peoplefound this instruction helpful.
Pamela from Great Neck, NY
Really Easy
Less than 15 mins
Screw drivers, Socket set
I replaced the dryer coils in 5 minutes!!!! It was so easy! If I called a repair guy, he would have charged me $200. I fixed the problem in 5 minutes, and all it cost me was the price of the coils...$15. Sweet!!! I upgraded the shipping to 2-3day, and the coils arrived the NEXT day. Great experience, and very satisfying to fix my own drye
... Read morer. The dryer works perfectly now and gets very hot!
Read less
Was this helpful?
Thank you for voting!
Heat 5 minutes keep working but cold air
0 of 1 peoplefound this instruction helpful.
J Miguel from Escondido, CA
Really Easy
Less than 15 mins
Pliers, Screw drivers
I saw some videos to have an idea on Wat to look for,most of them described the sensors and the igniter, but one specific mentioned the coils. I did the testing and because all the components were fine I concluded that the coils was the problem. Went online ordered the parts, 2 days later got them, took of the old ones installed the new
... Read more ones and the job was done drying perfectly. It cost me only $ 25 bucks and probably 10 or 15 minutes to fix it. Tanks part select You have an excellent service.
Read less
Was this helpful?
Thank you for voting!
the egnaighter lit, but was no flame on the furnes
0 of 1 peoplefound this instruction helpful.
Fausto from Palmdale, CA
Really Easy
Less than 15 mins
Nutdriver
well at first I thought was a sensor so i got it, did not work, second intent fuse end sensor kit, did not work, so I thought must be a valve, so I toke other look up on the price of the valve, then i find a kit to repair that specific problem, so I order it, I got it very quick over night, so I installed in 15 min, and walla!!! did work.
... Read more Thanks a lot. so if no flame, must be the valves...
Read less
Was this helpful?
Thank you for voting!
gas dryer flame light for about 1 min dryer run long time not dry
0 of 1 peoplefound this instruction helpful.
Brian from Katy, TX
Really Easy
Less than 15 mins
Screw drivers
took off bottom access panel replaced both electronic coils web site helped diagnose problem
Was this helpful?
Thank you for voting!
timer stoped working, and burner didn't light. gas flow was good so it had to be an electrical problem.
1 of 4 peoplefound this instruction helpful.
nicholas from riverside, CA
Really Easy
Less than 15 mins
Screw drivers
super easy 2 screws and my 11 year old son took 5 minutes.
Was this helpful?
Thank you for voting!
Broken knob
0 of 1 peoplefound this instruction helpful.
Bradley from West Olive, MI
Really Easy
Less than 15 mins
Pulled the old knob off and replaced with new knob PartSelect sent me the exact part you can't tell the difference.
Was this helpful?
Thank you for voting!
(Gas Dryer) with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on.
0 of 1 peoplefound this instruction helpful.
Bryan from West Branch, IA
Easy
15 - 30 mins
Screw drivers
Replaceing only this item fixed my problem with front panel removed Ignier would turn on, gas would light, ignitor went out as usual, but gas would shut off after a few minutes and not come back on. Note gas dryers are supposed to light, heat up, igniter stop flame stop after it gets up to temp, shut off for a while then repeat
... Read morethe process, it would have saved a lot of time researching to have known that earlier.. Take front panel off screws off, take panel off holding the 2 round coils in place, unplug the one with 3 prongs and replace, tested dryer with the panel off and the door closed so there was no suction issue. put panel back on 5 minute fix if you knew what you were doing.
Read less
Was this helpful?
Thank you for voting!
Burner would not kick on.
0 of 1 peoplefound this instruction helpful.
Willie from MOWEAQUA, IL
Really Easy
15 - 30 mins
Screw drivers
Removed Two screws took out the coils put in the new ones I ordered one day and got them the next day. Thank you partSelect For the quick service.
Was this helpful?
Thank you for voting!
Pilot would light but no gas from main solenoid
0 of 1 peoplefound this instruction helpful.
Stephen from Saint Anne, IL
Easy
30 - 60 mins
Nutdriver, Screw drivers
First I removed the two screws that hold the front access panel. After taking an ohm reading on the coil I found it was an open coil. I went on line to find out where to get the part. PartSelect web site was very complete when I enter the part number. I was able to make the purchase on line. The part was stock and it arrived in 3 days wi
... Read morethout any special handling. I then unplugged the solenoid, removed the two screws that hold the coils on. Replaced coil and bracket .Tested the dryer and it was working properly. Installed the front panel. PROJECT COMPLETE!!
Read less
Was this helpful?
Thank you for voting!
No heat
0 of 1 peoplefound this instruction helpful.
David from Crystal, MN
Easy
15 - 30 mins
Nutdriver, Screw drivers
I replaced the Thermal Fuse and Cycling Thermostat first, since they were listed as fixing the problem 45% of the time and 19% of the time, but the dryer still didn't heat. I then ordered and replaced the gas valve solenoids, which solved the problem (but I ended up breaking the dryer belt while re-installing the drum, so that had to be
... Read morereplaced too.) In hindsight, I wish I would have ordered all four parts up front and saved a bit on shipping. Installation was easy, especially with the diagrams that showed where each part would be found.
Read less
Was this helpful?
Thank you for voting!
would dry for 8 min. then no heat
0 of 1 peoplefound this instruction helpful.
Lindsey from Pacifica, CA
Easy
30 - 60 mins
Screw drivers
check the coils first. parts shipped to house within 24 hours. 29 bucks with shipping!
Was this helpful?
Thank you for voting!
No heat or intermittant heat
0 of 2 peoplefound this instruction helpful.
Brian from Round Rock, TX
Easy
30 - 60 mins
Screw drivers
MY issue was the heat would cycle up on a fully cold dryer, but if the Dryer stopped for whatever reason or started a sucessive new load, you'd get no heat. I could leave the dryer unplugged for 30 minutes and it would fire back up with heat but would go out shortly, or if lucky might finsh the load.
Most of the repair avenues
... Read morepoint towards the cycling thermostat or the flame sensor.
But It was the gas Coils.
It's Been perfect for couple weeks.
Great Site
Read less
Was this helpful?
Thank you for voting!
Dryer runs, but no hot air.
0 of 2 peoplefound this instruction helpful.
Michael from Hayward, CA
Easy
15 - 30 mins
Screw drivers
Unscrewed the front and ran the dryer. The heating coil DID get red hot but the gas DID NOT blow out. Unscrewed the cover over the top of the two coils. Disconected the wire. Replaced coil and cover. SUPER EASY. Its the starting and holding coil which lets the gas shoot out onto the heating filament. $75.00 just for the repair man to come
... Read more out plus parts, plus labor. Probably saved $200+. All the prints of the parts are on the website so you can see what your changing. TRUST ME....DO IT YOURSELF. You'll be glad you did!!
Read less
Was this helpful?
Thank you for voting!
No heat
0 of 2 peoplefound this instruction helpful.
Joseph from Lawrence, MA
Really Easy
15 - 30 mins
Nutdriver
UNPLUG Drier Remove bottom panel 2 screw Remove 2 connector to coil remove 2 screws lift off cover lift coil s reverse steps
My Orders
