KFCP KitchenAid - Instructions

Unlug refrig or turn off refrig from its control panel On/OFF switch.
For ease of work remove freezer shelve directly below the ice maker. Remove four screws from the bottom of the ice maker assembly, three that secure the ice maker and the other that holds a plastice shroud in place over the ice maker's power plug.
The ice make ... Read more r is now ready to be removed; it will slide forward by pushing up on left and right side of the ice maker's mounting slide rails. Once the ice maker is moved forward it is easier to disconnect its power plug (depress a locking tab on the side of the connector and pull connector apart and remove ice maker assembly.
Remove and replace motor module by removing three screws and and replace with new unit.
Reverse ice maker removal proceure for installation. Once installation is completed turn on Power to Refrig, Ice making should begin after a few hours.

Removed screw under ice maker. Tilted ice maker up to remove unit from upper two screws. Disconnected plug at rear of freezer. Attached wiring harness, baler arm and cover from old to new ice maker. Reinstalled in reverse order. Had ice within one hour. Very easy fix.

I did a few tests with the old ice maker and determined that it was the ice maker itself that was faulty. The replacement part I ordered exceeded my expectations in the time it took to get the part. I reused the arm, wire harness and clamps from the old icemaker. Then it was a simple install into the bottom freezer compartment, turning ... Read more on the water supply and bingo...lots of ice cubes.

The plastic drive gear broke and the unit was locked in the down position. The repair kit contained all of the parts required to fix the problem plus other replacement parts for the gear drive unit. It was very easy (about 20 min.) to replace the gear and other parts. The unit works fine now.

I unhooked the wire harness from the ref. and took out three screws and pulled the old unit out. I than changed a few parts from the old icemaker to the new and reattached the new ice maker to the ref. and plugged the wire back in. everything is working fine. No problems. Also I was very happy with the ordering process. Thank you!!

I did not unplug the refrigerator. Your choice on this. Take a close look at the existing icemaker, how the wires are routed and what the water spout looks like as it relates to the icemaker. Small flat-blade screwdriver will help in unlocking tabs on the icemaker plug. Go ahead and unplug it. Of the three screws that secure the icem ... Read more aker, two are impossible to see without holding a mirror in your third hand. Completely remove the bottom screw (by feel). Don't drop it, like I did. Have no idea where it went. Loosen the top two screws but do not remove. Icemaker will lift off of the top two screws when you push it up. With old icemaker out of the way, plug in the new icemaker. Be careful to properly align the water spout into the new icemaker as you hook it on the two top screws. When everything looks good, tighten the two top screws. Replace the bottom screw, if you didn't lose it. My icemaker is doing fine without a bottom screw. It should make some ice within an hour, or so. Mine did.

The troubleshooting time takes about 20 to 30 minutes. After checking out the solenoid (valve water), the water line, and the electronic board (emitter/receiver) are working fine. The only thing left is the ice module. I called Partselect and talked to a sale rep to make sure I get the right part, and the lady was so helpful by sendind th ... Read more e picture of the part so I can review before ordering it. I received the part in 3 days ( normal shipping) and did the folowings:
1) Unplugged the power cord from refrigerator.
2) Removed the ice module by removed a 1/4" screw from under the right side of the icemaker that retains the icemaker and a “U” plastic clamp and then pull out the whole unit it from the track.
3) Unplugged the cable connected to the ice maker.
4) Using the phillips screw driver to remove the 3 screws. Carefully pulled out the ice module and installed the new ice module.
5) Put the ice maker back to the freezer, plug the cable back to the ice maker and put the clamp and tighten the nut.
6) Plugged the power cable back to the wall.

The first ice I got in an hour and a full bucket of ice in less than 24 hours. I spent less than $80 for the whole thing. Thank you so much Partselect for the great service and the stories posted, it really helped me to get it done.

The repair didn't get done, because both times that I requested a 25-Watt Light Bulb, I received a 3.6 Watt bulb instead & neither one worked. So I tried testing the original bulb in a table lamp & it worked. So I sense that the problem may be in the switch that allows the light to turn on when the drawer is opened & shut off when the d ... Read more rawer is closed.

Unscrew decorative plastic cover. Unsnap old damper assembly and disconnect wire connector. Snap in the new assembly and plug in the wires. Replace decorative cover.

Ez job. Perfect fit.

Watched numerous U tube videos to prepare ourselves as well as instructions from other posters. Tried to pay attention on how we disassembled thing with limited success. Installing the new end caps proved to be easier that we expected since they weren’t screwed in but just snapped in. We think that’s because it’s a newer model that what w ... Read more e saw on U tube.

I first replaced the lower (freezer) evaporator thermistor based on recommendation from other feedback, however that did nothing to resolve the problem. I subsequently discovered a diagnostic document hidden under the upper right door hinge, which helped me narrow the problem down to the upper (refrigerator) evaporator fan motor. After r ... Read more eplacing the fan motor, my refrigerator is up and running again. The only challenge was accessing and removing the access panel(s) and air column. Once those were removed, replacing the fan motor was simple.

First let me say that I read many of the other posts regarding this repair and without them I wouldn't have had a clue how to fix this. Since the ram apparently moved up and down when I shut it off and turned it back on I reasoned the directional switch must be the problem. Ordered the part, Quick delivery. To replace the switch I removed ... Read more the draw and removed two screws on the frame that hold the control panel in place. Lift up to remove. My unit is a stand alone unit although it is installed under the counter. There are two additional screws to remove the top and expose the ram and power screw drives. To remove the directional switch from the control panel you need to remove two hex head screws that hold it in place. This is a little difficult because of the small space. With the help of a small nut driver I was able to remove it. Note: the screws are held in place by a flat piece of metal that acts as a nut. Be careful not to drop it. Then simply remove the wire leads (all color and letter coded) and remove the switch. I was careful to reattach the leads to the new switch as I removed each one. Be sure to replace the switch with the limiting lever in the same position as it was in (it is vertical). Put everything back together and you should be good to go. That didn't happen for me! Problem persisted! Next on my list was the power nut. I got access to the ram and power screw drives (see above for instructions). The two power nuts are plastic wing nuts that are held in place by metal covers. The metal covers are each held down by two hex head screws. To gain access to the power nuts you have to remove the metal covers. Note the position of the nuts in relationship to the power screw shafts so that when you reassemble it they will be in the same position as when you started. In my case the top of the screw shafts were even with the top of the power nuts. (CAUTION: the ram is held by this assembly. Depending on what position your ram is when you started this repair it may fall! My ram was in the up position and when I removed the second cover it slammed down to the bottom of the drive screws). My advice is to be prepared by bracing up the ram before removing the metal covers. No harm when the ram fell but it did startle me. I then removed one of the power nuts. It was split in half. The other nut was fine but I decide to replace it anyway. Ordered parts. Quick delivery. Before I attempted to replace the power nuts I removed the ram (it just lifts out) and cleaned every thing. I put some new grease in the places that I had removed it. Then sprayed WD40 on the power screws. When I put the ram back in, I broke the new directional switch I had put in. So be careful!!! I still had the old one so I ultimately put it back in. I then replaced the power nuts. This was a little difficult because I had to hold the ram up while I was putting the metal covers back on. I would suggest you either brace the ram or get someone to hold it while you put the metal covers back on (In retrospect I suppose I could have just put the nuts on when the ram was down). Reassembled everything. Should be good to go. That didn't happen for me! Problem was still there! I turn it on, ram goes down. I turn it off, ram goes up. Desperation!! The only other thing it could be is the drive gear assembly. Ordered parts. Quick delivery. The gear drive is on the bottom of the machine. Lay the machine on it's side to gain access to the bottom cover. There are 5 hex head screws that hold it on. Remove screws and cover. It's pretty simple from here. The drive gear was missing a few teeth but the rest were in tact. This explains why the ram was still moving up and down and led me to believe it was something other than the drive. The only difficult part was the removal of the pin in the drive shaft. I wound up using a bolt the about the same diameter and a hammer to drive it out. Then just reassemble. There are some instructions that come with the gear parts that tell you how to set the spacing in the gears but I had no problem just replacing the parts without making any "adjustments". Should be good to go! Yessssss! Everything worked perfectly!!! My final words of advice. If your machine has this problem CHECK THE DRIVE FIRST. It the easiest thing to do because you can visually inspect it and know or eliminate it as the problem. It's about a 5 minute job and can may save you some of the problems I had. A big thanks to PartSelect for sponsoring these posts. The repair company that I normally use told me the machine was too old and probably wasn't worth the $100 just to come out and look at it, never mind the additional cost to repair it. All in I spent less than $100 and had I checked the drive first, I could have been done for less than $30.

Like others who experienced this problem, I removed compactor from under the counter and laid it on its side. I removed the screws holding the cover plates to the motor and gear/chain box. The larger (4" +/-) plastic drive gear which moves the chain that lowers or raises the compactor ram was broke. Using a socket and ratchet, I turned ... Read more the shaft the gear was attached to in a counterclockwise direction and moved the compacting ram from the bottom position to the top so I could finally open the door, It takes a lot of turns to move the compacting ram to the top so be patient. I then loosened the bolts, in the base, that holds the motor secure and slid the base toward the broken gear putting slack in the chain. I removed the split ring from the shaft and removed the sprocket which originally is part of the gear but was left on the shaft when the gear broke in three places. I elected to not remove the original washer and spacer and put the new gear with sprocket on the shaft, put the chain on the socket and installed the split ring. Slid the motor base back to original position putting slight tension on chain and a proper clearance between the gear and drive shaft (sheet of paper seperation). Reinstalled the covers, tested and was finished.

Hardest part is access to the icemaker itself. Once I removed the freezer door (bottom drawer freezer), and got the sliding basket out, it was a 10 minute job. Make sure you start the upper screws first, the icemaker will hang there while you adjust, connect the harness, and tighten. Make sure you are ready before you close the door, it ... Read more will start making ice as soon as the door is closed.