EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KESS907SSS00 KitchenAid Range - Instructions

All Instructions for the KESS907SSS00
91 - 105 of 133

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
When removing the warming drawer I did not read the instructions and broke the slide for the drawer. I removed the drawer without pressing the tabs which broke the right slide.
  • Deborah from Ashburn, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I removed the broken slide by removing 1 screw on the front slide and the back of the slide came out of the slot in the very back (no screws). I fitted the back of the slide into the slot and then replaced the screw on the front of slide. Extended the slides then I pressed the tabs on the drawer and replaced in onto the slides (left an d right) . Closed drawer and finished! Very easy!
Was this helpful?
Thank you for voting!
Power block terminal failure
  • Leonard from Brazoria, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Ordered part needed. Much, much cheaper than purching a new range.
Was this helpful?
Thank you for voting!
The inner heating element was not working
  • DENNIS from ROWLEY, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
The range top came off with two screws under the front portion of the glass top (by the oven door). I unplugged the connection plugs at the rear off the range top, unscrewed the rear screws holding the heating unit in place and plugged in new element and reassembled range unit. You need to removed the two phillip head screws at the rear o f the range top in order to remove the bar holding the heating element. Once you do this it is very easy to finish the job.
Was this helpful?
Thank you for voting!
replace two stove top burners
  • Howard from CHESHIRE, CT
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
It was very easy. Disconnect the electricity. Take the two screws out that hold the top in place. Raise the top and with the pliers change all the electrical connections and retaining bars. Install the two new burned tops. Lower the top and re-install the two retaining screws.
Was this helpful?
Thank you for voting!
Terminal Block was melted where the cord had came lose.
  • Louise from Humansville, MO
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Removed the therminal block and put the new one in.Using a screwdriver, very easy repair.
Was this helpful?
Thank you for voting!
The Terminel Bloc Overheated And The Bloc Melted Causing The Stove To Cease Fukshioning
  • Joseph from Channelview, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
R&r
Was this helpful?
Thank you for voting!
Missing oven racks
  • Deb from Eastvale, CA
  • Really Easy
  • Less than 15 mins
We have double wall ovens and each one only had a single oven rack in it. After 3+ years, I was tired of dealing with the issue so I ordered two new racks from PartSelect. They came quickly and fit perfectly. All I had to do was open the box, remove the rack and slide it into the oven. No muss, no fuss. Why didn't I do this years ago ??
Was this helpful?
Thank you for voting!
Remove racks before self-cleaning
  • Michael from Waxhaw, NC
  • Really Easy
  • Less than 15 mins
Similar to another customer, the racks were not removed before self-cleaning. The issue was that I AM THE HUSBAND and I admit that I did it. Ooops. Great price and if I do it again, I will go back to parts select to get a replacement.
Was this helpful?
Thank you for voting!
not needed
  • Peggie from Gresham, OR
  • Really Easy
  • Less than 15 mins
screwed in the new oven light
Was this helpful?
Thank you for voting!
Worn and discolored oven door gasket
  • John from Fort Worth, TX
  • Easy
  • 15 - 30 mins
  • Screw drivers
Removed retainer screw and retainer. Removed old gasket. Installed new gasket, retainer, and retainer screw. Very simple job.
Was this helpful?
Thank you for voting!
Wiring Block shorted due to moisture and Stove had no Power
  • John from Roberts, MT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
This was very straight forward. Once the sheet metal shroud on the back side was removed just had to undo the one remaining wire, remove the block, and reassemble. Only question I had was which wires went where. The Wiring Block was melted due to the short and the wires were no longer attached. Did a quick google for a typical oven three- wire install and that did the trick.
Was this helpful?
Thank you for voting!
Upper double oven would not heat following a power failure during the clean cycle
  • Layla from Carmel, IN
  • Easy
  • 15 - 30 mins
  • Screw drivers
I turned off the power from the circuit breaker. I then removed the doors and the trim package from around the oven. I slid out the oven and had my husband help me lower it to the floor. I removed the back covering and then removed the wires connected to the old thermostat. I unscrewed the old thermostat and replaced it with the new ther mostat. Did everything in reverse and it seems to be working very well. It took about 30 minutes total. Some sites suggested that a fuse needed to be adjusted/replaced. In this kitchen-aid double oven and I'm assuming whirlpools as well, the thermostat/fuse is one piece located on the back of the unit. It was very simple. The piece cost $47. Such a great investment of time and money. I had the piece in 2 days, without paying extra postage.
Was this helpful?
Thank you for voting!
While trying to tighten the oven door handle, the outside glass shattered.
  • Rick from Spring, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I was not able to order just the glass, so I ordered the exterior door assembly. The door assembly is held in place by 5screws. 2 on top, 3 along the bottom. A very easy project!
Was this helpful?
Thank you for voting!
Center of Front Burner not heating up
  • Bob from Aberdeen, NJ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Ceramic cooktop: Turn off power to the unit. remove long "locking" screws from underside of the unit; remove clips (may take a little effort if they are "frozen" in place) From underneath unit lift it up and out of the counter - do not try to lift from ceramic top- remove 4 control knobsun - remove 12 screws (3 per side) attaching ceram ic top to the unit - carefully work ceramic top off the bottom frame; its a friction fit - do not force it. Place ceramic top in a safe, flat space. Note the orientation of the burner - you will need to replace the new one in the exact same orientation - also note the connections on the existing unit and match them to where they will go on the new unit. (note: my old unit had a black wire that was replaced by a solid metal strip) work the wire clips off the existing unit, flip it ove and note the number on the "clock face" where the spring clips attach. You may need to drill a small pilot hole from the top side. remove the spring clips from the old unit and place them on the new unit. These clips align the unit in the proper location and provide proper contact with the bottom of the ceramic top. Replace the top gentley working it onto the base and replace the 12 screws. Place the unit back in the countertop being careful to lift up to reposition so you don't disturb the foam tape along the edge of the opening. Replace the clips in the side of the unit, replace the mounting screws, replace the control knobs, turn power back on. You should be done. Takes about 30 minutes.
Was this helpful?
Thank you for voting!
element went bad would not heat
  • Bruce A. from Adena, OH
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Removed screws that hold element remove wires from old element replace with new one replace screws turn power back on at breaker box done.PS make a steak done.
Was this helpful?
Thank you for voting!
All Instructions for the KESS907SSS00
91 - 105 of 133