EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KESS907SSS00 KitchenAid Range - Instructions

All Instructions for the KESS907SSS00
76 - 90 of 133

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven light bulb inop
1 of 2 people found this instruction helpful.
  • Ed from Canyon Country, CA
  • Easy
  • Less than 15 mins
Taking off the glass lense for the light bulb was harder than I thought. It unscrews counterclockwise, but it was very hard to get off. It would not turn. I ended up using connector pliers I use for work, that has rubber jaws. The lense unscrewed very easy with it. Light also unscrews out. PartSelect.com is the only way to go to buy parts for appliances. It is simple, even has the illustrated parts catalog. And it saves a lot of time and gas, driving around looking for the part!!. PartSelect came through again.
Was this helpful?
Thank you for voting!
The side trim on the glass door needed to be replaced.
1 of 2 people found this instruction helpful.
  • Mary from LARAMIE, WY
  • Easy
  • Less than 15 mins
  • Screw drivers
After we put the latch pins in, the door was easily lifted off. We placed the door on the table and unscrewed the trim pieces. The new trim pieces went into place after we cleaned the door. We slipped the door back on the oven and removed the hinge pins.
Was this helpful?
Thank you for voting!
Bearing on cooling fan.
1 of 2 people found this instruction helpful.
  • Mary R. from Thornton, NH
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed old fan by removing all screws except the back two lower screws - here I cut the flange on the old fan to remove. Drilled the back two bottom holes so as to fit over existing screws then replaced the top 3 and bottom 2 screws as well as power leads. Offset screwdriver is a must.
Was this helpful?
Thank you for voting!
wire came loose and shorted out
1 of 2 people found this instruction helpful.
  • Elizabeth from HOUSTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Ordering the part online was easy. It arrived in a timely manner. I found a terrific video online showing how to install the terminal. It was so easy. Thank you for the great instructional video.
Was this helpful?
Thank you for voting!
Not heating up properly
1 of 3 people found this instruction helpful.
  • Harmon from MONTICELLO, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Installed a new thermostat and noticed the convection heating element wire had burned in two. Ordered new element and installed. Oven is currently working properly again.
Was this helpful?
Thank you for voting!
the burner didn't work and digital part too
8 of 24 people found this instruction helpful.
  • Eduardo from Lenexa, KS
  • Easy
  • 30 - 60 mins
  • Wrench set
I used the digital multimeter for measure the voltage in the burner and in the digital part,I saw the electric cables
Was this helpful?
Thank you for voting!
broken meat probe
0 of 1 people found this instruction helpful.
  • Daniel from Massey, MD
  • Really Easy
  • Less than 15 mins
My story isn't so much about the repair but the fine service from part select. My 1st order was lost at delivery at our house. Part select quickly corrected the mishap with no issues. This kind of service is much appreciated.
Was this helpful?
Thank you for voting!
Block broke
1 of 4 people found this instruction helpful.
  • Edward from Crimora, VA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done
Was this helpful?
Thank you for voting!
The oven shipped without a temperature probe.
0 of 2 people found this instruction helpful.
  • jerry from rochester, NY
  • Really Easy
  • Less than 15 mins
Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
range installer broke a screw off & busted the plastic piece
  • Christina from West Des Moines, IA
  • Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Had to screw off old terminal block & screw on new one
Was this helpful?
Thank you for voting!
Burned out heating element for radiant heat burner
  • Jay from Brevard, NC
  • Easy
  • 30 - 60 mins
  • Screw drivers
I watched the video, purchased the correct heating element and did the repair as illustrated in the video. I simply removed the cook top, removed the ground wire, removed the wiring harness, removed the failed heating element, installed the new heating element and reinstalled the wiring. Piece of cake!
Was this helpful?
Thank you for voting!
terminal block cracked
  • James from Richmond, VA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
Followed the easy instruction sheet provided.
Was this helpful?
Thank you for voting!
replace thermo fuse
  • mike from king city, OR
  • Easy
  • 30 - 60 mins
  • Screw drivers
turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse it took about two hours. second time it about an hour.
Was this helpful?
Thank you for voting!
Melted and fused together wires due to non-grounding of terminal block
  • Dr PauMari from Alamogordo, NM
  • Really Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
We called a dear handyman church member with years of repair service to his home, personal vehicles and general maintenance of our little church and parsonage. Known for his trade as an engineer with over 50 years in the industry wearing white shirts and working in an office; however, he is not afraid to get his hand dirty. We all worked together (my husband, daughter and me) to troubleshoot and resolve the problem and the terminal block purchased from "parts select" was just the answer to all our problems and worries. The range is fully operational and works like new. Thanks.
Was this helpful?
Thank you for voting!
All Instructions for the KESS907SSS00
76 - 90 of 133