KECD805 KitchenAid Cooktop - Instructions

Open oven door and remove two screews with 5/16 nutdriver to remove hole top of stove.Just lift up gently on front of top and pull toward you and when about 4 inch clearance on back of top you will see where all the wires connect ,press the side tabs of this big connector and it will release very easy to remove the top.Place top on bath t ... Read more owell upside down on countertop and remove 4 screws and 2 clips on the bad burner with the same 5/16 nut driver and remove the three wires and reinstall the same way then reinstall the top on the stove in the same order.Very Easy Job

first I checked continuity through the surface element (burner) switch (rheostat) which was fine. then found the screws holding the burner top on and removed, this made it possible to lift up the burner top and remove the burnt out surface element.which was easy to see. take down the number, buy a new one and re hook up the four wires to ... Read more the new element. (always mark down where the wires went)

I did exactly what your instruction video showed. The most important thing to remember is to TURN THE POWER OFF FIRST.

Removed top of stove replaced heating element ,piece of cake.

i did fine

1. I ordered a replacement heater element from Parts Select, which arrived in just 3 days at my home. 2. I turned off the main circuit breaker to the range. 3. There are two small sheet metal screws inside the top left and right side of the oven door frame which need to be removed first in order to lift and remove the burner top from t ... Read more he range. 4. After lifting and pulling the burner top toward me about 6 inches, I unplugged the left and right burner assembly wiring harness connectors. 5. I lifted the burner top assembly off the stove and turned it upside down an a table. 6. There are six sheet metal screws that need to be removed to allow the sheet metal panel holding the heater assemblies to be lifted off and then also set upside down on a table top. All five burner elements are now visible. 7. Disconnect the slip-on electrical connectors to the specific heater assembly that is defective. 8. Unscrew the three small sheet metal screws from the three spring clips that support the heater assembly on the sheet metal panel; re-attach the spring clips to the new heater assembly. NOTE: Either memorize or record the position numbers that are cast into the ceramic housing of the burner to replace the new burner in exactly the same position. 9. Insert the three spring clips back into the sheet metal panel where the old, defective burner assembly had been removed. 10. Re-connect the slip-on wire clips to the new heater assembly in the same position as they were removed from the defective heater assembly. 11. Turn over the sheet metal panel with the burner assemblies attached and replace the sheet metal screws holding the panel to the stove top. 12. Turn over the stove top assembly and set back onto the range allowing space to reach to the back and re-connect the polarized connectors to the left and right side burners. 13. Slide the stove top back to the rear and carefully lower the front edge back down with the two metal tabs inserted back into the oven door frame. 14. Re-install the two sheet metal screws that hold down the stove top. 15. Turn on the main circuit breaker to the range. 16. Carefully test the new heater assembly by turning the range control knob to LO heat and watch for the stove top burner to momentarily turn red with heat. 17. Turn off the range control knob. 18. You are finished. It was a very easy installation.

Removed the two screws, on both sides of the oven wall corner. Gently lift the front end of the glass top and pull towards me and disconnect the two electrical sockets. Carried the glass top assembly on the kitchen table and turned upside down. Removed the six screws. Removed the assembly from the glass top. Turn the top burners asse ... Read more mbly over and disengaged the two clips of the burned out burner from the assembly plate. Transferred the two clips to the new burner on the exact locations like the old ones were. I have placed the new burner on the location and snapped the clips on the slots. Removed the connectors one piece at a time and connected to the new burner. Reversed the previous disassembly and all was done Works like a charm. Thank you all for assisting me in providing the necessary parts and video instructions. It was a lot cheaper than to buy a new range.

Although I put 15-30 mins for repair, most of that was taking it apart only to have to put it back until I got the right part. It can be done in 15min or less. FIRST: UNPLUG THE RANGE or Shut the circuit breaker OFF. Remove two screws (1/4" nut driver) on the front lower edge of the cooktop. These are seen once you opent the top oven door ... Read more . Lift up the top and pull out about two inches and disconnect the multiwire plug in connector. Lift the top off the range and place it upside down on a flat surface (talbe or counter) protected with a towel. Unplug the sliding connectors from the burner unit noticing the correct placement. Remvoe the two tabs (#2 phillips screwdriver) on either side of the burner unit noting location. Take the time to clean up all debris with a vacuum or soft cloth. Install the new burner, connect the two tabs, plug in the connectors, return the top to the range, plug in the multiwire plug, secure the two screws and plug the range back in and start cooking!

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Repair video was very helpful. I have removed the screws on both sides of the appliance under the surface plate, in the front. The Owen door has to be open for that. Then I have pulled the surface plate for a little space to disconnect the two connectors. Turned the surface plate over on the kitchen table, removed the 6 screws. Turne ... Read more d the burners assembly over and removed the small burner by disengaging the two clips. I have removed the 2 clops from the burned burner and assembled it to the new burner. I have placed the burner and engaged the 2 clips with a crownose players. I have removed one electrical connecter at a time and connected to the new burner. I have turned over the assembly over the glass plate and assembled the back cover with 6 screws. Put the surface plate on the range and connected the 2 connectors, pushed back, lined it up with the 2 screw holes in front of the range on bot sides and put the 2 screws in and Finished.

unscrew 3 screws under the control panel and pull that away from the glass top making sure the wires don't come apart from the connectors. care fully slide the glass forward and replace the burner which was the easy part. DO NOT try to test without making sure that none of the burner are touching the metal surface!!!!!!!! it will trip you ... Read more r breaker. But now we have a range with 4 burner after a year THANKS

First, I turned the circuit breaker off to the range. Then, I pulled the range out so that I could get to the screws which held the glass top in place. They were located on the sides of the range. I had to remove the trim pieces on the sides to get to the forward screws. Once that was done, I lifted the glass top, unplugged the wire harne ... Read more ss, flpped it over on a protected surface. I noted the numbers on the old coil where the clips held it in place and put the clips on the new coil in the same place. The old wires just clipped on to the new coil exactly as they clipped on to the old coil. I put it all back together and it works great! I am a 70 year old woman who did this all by myself. You young guys should have no problem.

1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. ... Read more 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

Got a new fan switch. Removed the heater dials. Disconnected exhaust tube from blower (it was sealed with aluminum tape). Lifted cooktop straight out of the counter-top, rotated it a little so that it would rest on a pair of 2x10's I set at the extreme corners of the counter-top cutout. After that it was real simple - unscrew the tang ... Read more s from the sheet metal. Then use a screw driver and gently pop the glass free of the sheet metal housing. Once the glass is off, unscrew the control panel cover and rotate it over. The switch is mounted with a jam nut - remove that and disconnect the cables. Reverse the process with the new switch. Only beef I had was the housing sent by part select was damaged, so I had to swap the electrical innards to get the thing to work. It took 60 minutes and most of the time was spent cleaning the baked on food off the cooktop and countertop. Had to use a razor blade to scrape the crud off. Actual repair without cleaning was 20 minutes.