KECC560 KitchenAid Cooktop - Instructions

Removed unit from counter, removed 14 screws holding glass top to frame, removed ceramic element, swapped over mounting brackets to new element, checked wireing as per instruction sheet (direct replacement) connected wires, re-installed glass top to frame and placed back into counter. ops check good.

Thanks for the previous viewer's tip, disconnect power, pushed the cook top out of the counter and used a wood block for the support. Unscrew the smooth top from the burner, remove old and plug in the new one. Connect power, test OK. Put everything back.

Dual Burner switch was a replacement and not the same as original - instruction sheet gave excellent replacement instruction with color coded wires and numbers too follow, 6" switch was same as original so no problem with either switch replacement - stove now works like it was new.

Removed glass surface and identified existing wiring (sketch, photo, schematics) before disconnecting and removing it. Installed the new switch and connected the wires using the supplied wiring instructions as well as my sketch and schematics. Appreciate that the new switch came with wire extenders and shrink tubing. Had to use both of th ... Read more em.
Replaced the glass top and installed it back into the counter ,Turned on the circuit breaker and everything worked perfect. Just want to mention that I am extremely satisfied with PartSelect service. It is second time I ordered cooktop part. The delivery is prompt and the parts work as required

Removing the stove top was easy, it was just setting in place. Put some blankets over the kitchen island and did the repair their. Most difficult thing was, how stight the wires were. After removing the switch cover, I wound it nessary to remove the inside side wall of the switch box in order to have enouph room to change the switch. Work ... Read more s just fine now. Thanks for your service.

1. Remove power from unit. 2. Removed 1/4" sheet metal screw from lower blower vent tube. 3. Lifted the unit above the counter and placed two 1x2" boards between the unit and counter. To remove the Stove Top to get access to the Element you must remove 8 each 1/4" sheet metal screws from the bottom side of the Stove Top attaching flange. ... Read more 3 each screws on the forward and aft side and 1 each on the left and right side. (Note, the 8 each 1/4" attaching screws are at the top of the Stove Top attaching flange.) 4. Remove the Vent Grill and locate the 2 each cross point screws on the center left and right side of the opening. (Note. Due to the limited space, I used a right angle cross point driver.) 5. Remove Stove Top. 6. Tag electrical connections. Remove and replace Element. 7. Turn on power and check Element. Remove power and Reassemble Unit.

We lifted the glass top, uninstalled the old burner and installed the new burner in it's place. It worked right away - and is still working. No other tricks the new burner was a perfect fit.

I broke the correct post from the new cluster of post selections and stuck it on. I had the kit for a couple of weeks before I realized that this was not an electrical problem. It would have been good of you to send only the new plastic post. That kit was intimidating for a 73 year old woman who lives in the country and does most of he ... Read more r own plumbing and other household repairs. The repair took less that one minute.

We had been missing it for years. Perhaps it melted, maybe the dog. Anyway, Home Depot didnt have the match. I order the exact knob, received it in a very timely manner. Took it out of the package, and without any tool, placed it it it rightful spot. My wife is happy now. Thanks for helping me.

Replacement was simple. Old switch was easily removed. Once I swapped the wires from old to new we were in business. One thing I would do differently than the included directions called for. I wish I had waited until I had installed the new switch to set the shaft length. I snapped off one too many sections of the shaft after measuring th ... Read more e original shaft as recommended. If I had installed the replacement switch and then set the shaft length it would have been more accurate. Everything still works but one knob is now slightly lower than the other three.

Removed two screws holding cooktop to oven. Unlike the video, the cooktop was not detachable as the wires were hard-wired to the range, so I had to prop the top up with a 6" block of wood and was working upside down. I replaced the element and everything worked just fine.

Followed the instructions in the switch kit. Unpluged range glass cook-top power cord. Lifted smooth cook-top out of counter hole. Removed about 10 sheet metal screws around box/glass surface interface. Removed all 5 infinite control power switch knobs vertically. Lifted glass cook-top from element box. Set cook-top aside on edge away fro ... Read more m work area. Flipped switch control box cover and identified which switch was to be replaced. Noted colors and terminal post data. Replaced 1 wire at a time per the kit instructions. Reversed procedures. Turned unit on and confirmed proper function. That was it!

Lifted the range top about 2 1/2 inches, removed the ceramic top and replaced the burner. Tested the burner before replacing the top. Everything worked fine.