KECC560 KitchenAid Cooktop - Instructions

First I reviewed a video on YouTube by this site. Even though the range on the video was not the same as mind, it gave me an idea on what to do. I proceeded to pull the rang out from the wall and disconnected the power plug. Next I removed two screws from the back located on the left and used a flat blade screw driver to depress two brack ... Read more ets on the front to release the glass top panel. I unplugged the wiring harness and disconnected the grounding wire and took the glass panel off and laid it upside down on the kitchen table. I removed the old heating element first by unplugging the wiring and removing the brackets that held it in place. Installed the new one, plugged in all wirings, brackets, screws and replace the top back on the stove.

The repair was very easy. There were 3 screws under the front lip which had to be removed. This allowed the smooth glass top to be removed, tilt and pull forward. This exposed the burners and the unit I purchased was a direct replacemt for the burnt unit. All I had to do was remove the electrical clips from the old unit and put them on th ... Read more e new unit. There were 3 spring elements, each with 2 screws, which held the unit in place.

Opened the Cooktop. Hardest part was removing the cooktop.
The heating element was broken, very hard to see.

Remove 2 clips and install in new element. Great oppurtunity to clean the unit.

This is a slide-in range, so I:
1. Turned off the circuit breaker for the range. The range is hard-wired, so can't just be unplugged. I determined the clock on the range went off.
2. Removed 4 screws holding the front control panel to the cooktop. Removed 2 screws from each side panel into the cooktop. Removed 4 screws from the ... Read more rear panel holding the cooktop.
3. With my assistant (my wife) lifted the cooktop and tilted it so that I could access the underside.
4. Used an iPad to take photos from several angles of the wire connections from each burner control. Printed the one showing the connections on the dual burner control.
5. Removed the 4 screws holding the sheet metal support for the dual burner and one of the other burners. Released the spring steel retainers holding the dual burner. Removed the burner.
6. Used the iPad again to take photos of the connections to the dual burner, and printed it.
7. Removed all the wire connections to the burner. Checked continuity from the center (common) terminal to each of the other terminals. Determined that in fact the inside coil was open (burned out).
8. Removed the two screws holding the spring clip retainers on the old burner. Matched the old and new burners to determine where the spring clips should go. Drilled 2 small holes in the base of the new burner and screwed the clips from the old burner on the new one.
9. Now the tricky part: The new burner didn't have the exact same limiter and heat sensor probe as the old one. After several false starts, we were able to barely make out the terminal letter/number designations on the control and match them to the same letter/numbers on the new burner. It required a magnifier and a strong flashlight to read these engraved markings.
10. Made the connections on the burner. I used a pair of long-nosed pliers to carefully pull the connections off the spade terminals, and attch them on the new burner.
11. Mounted the burner to the sheet metal support using the spring clips previously installed.
12. Re-attached the 4 screws holding the burner support to the cooktop.
13. Carefully replaced the cooktop onto the range, paying special attention to not pinching any of the wires, and making sure all the wires, from all the burners were still connected.
14. Replaced all 12 screws holding the cooktop to the range.
15. Turned on the power, and checked all burners, including the new one, to see if they were opetating properly. YAY! They all worked!

It must be noted that we had to call a repairman to troubleshoot our installation the first time. We had reversed two of the wires to the new burner, because of the difference between the old and the new limiter connections. The engraved markings in the porcelain were very difficult to see. The instructions that came with the new burner never addressed this issue, and instead had very confusing (and worthless) instructions about replacing the limiter from the old burner to the new on. (This was not possible, anyway).

After the repairman left, we discovered the front burner that had been working, no longer was. With our newfound experience, we repeated the previous steps to take the range apart and discovered one of the wires had become disconnected from that burner. We re-connected it, re-attached the cooktop, and everything worked.

One telltale indicator that we had mixed up the connections on the burner, was the red "hot' warning light on the range top came on as soon as we restored power, even though no burners had been on. I should mention that the dual burner "worked" a couple of times even with the reversed connections, but then failed to work any more.

Turned the breaker off. Removed the glass cook top and removed the screws holding the cook glass to the metal burner case. Followed easy instructions removing one wire at a time and placing on the new switch. Put the glass top back on and installed screws. Placed back in the hole and turned the breaker on. Works like new.

Got Model and SN, went on line and located correct part. Ordered part, arrived in 3 days. Started repair by turning off power to stovee top. Got putty knife and went around edge to loosen stove top to raise and het to underside to dismantle cover. Used battery drill to remove screws on cover. After accessing and removing top and bottom, r ... Read more emoved 2 screws, changed one wire at a time and replaced on new switch, reassembled in reverse, turned on power and happily watched burner come to life with new switch.

Called an authorized Kitchenaid service technician after ordering part. This was the second time this switch has required replacement so we saved time and money by ordering the part in advance from PartSelect. The trickiest part of the repair was separating the ceramic top from the rest of the cooktop. Had we attempted to do this ourse ... Read more lves, we would have given up at that point. I would only recommend this as a do-it-yourself repair if you are intimately familiar with how these cooktops are put together. It is fairly easy to break the ceramic top if you're not.

I found the received switch (PS12070192) a poor replacement for the original, or even the earlier replaced part (PS11744446, in 2016) I was going to replace since the press/return feature seemed slow to return.

The male spade lugs on the received switch are so positioned that engagement is only possible if the lug is bent out ... Read more at a large angle. The lug set-back from the body edge, and the raised ribs on the sides still prevent full engagement of the connections.

I did install the new switch but found that was the only switch that didn’t give a signal light when turned on.

I have reinstalled the earlier unit.

Is part# PS 11744446 no longer available?



James E Weimholt. [email protected]

Lifted range top, disconnected and labled wires from old switch, removed old switch, replaced wires on new switch, installed new switch.
NOTE: Local appliance store informed me that the electric cooktop was too old and that a replacement switch was not available and wanted to sell me a new cooktop for $795!
I found the switch ... Read more on PartSelect and repaired the cooktop. Total cost... UNDER THIRTY DOLLARS!!

Turned off power to cooktop and double checked
Lifted up entire cooktop and rested it on two pieces of wood that spanned gap underneath
Removed screws from around edges to free the metal framework that holds the cooktop in place-- this requires spinning the cooktop a bit to get access to the back.
Lifted metal framework off ... Read more
Lifted glass from cooktop off
Checked configuration of power plug ins against new part and noted where they should go. There was a slight difference of how plugs were arranged, but it was easy to logic out.
Removed old burner unit and plugged in new one. Ensure that nothing was touching contacts.
Replaced the glass top onto cooktop
Put metal frame back in place and screwed in
Lifted entire cooktop, removed boards, and lowered back into place

First, the diagram on your website said remove two screws. The diagram looked like they were on the back of the stove on each side. On my stove there were three screws that were visible under the front lip upon opening the oven door. I removed the top, which comes completely off and set it aside. Be careful when removing the top. Don ... Read more 't drag it out, otherwise you'll tear up the asbestos around the other burners. Two people would be better for the inexperienced people. The new elements have been redesigned, so the diagram doesn't fit what you are looking at. Plus, the diagram on paper is looking underneath the element when you are looking down on the top of the element. I removed one wire and put it in the same spot on the new. Turned out it was not the element that was bad. It was a loose wire in the inside of the control panel.

Turn Circuit breaker off.Open the Oven door removed the 2 screws to the top surface. Disconnect the wire harness mark and remove the wires from the Old Element, removed the screws holding the element to top surface, Remove element replace with new element. Install wires, install screws, reconnect wire harness reposition surface. Reinstall ... Read more screws and turn Circuit breaker power back on. Done and Done

Turned power completely off. Removed knob from front panel. Opened range top cover. Removed 3 screws from aluminum panel protector behind the element switch. Once panel is removed you can see the switch element. Remove 2 screws from the front panel that connects to the element switch. Remove the old element and replace with new element ma ... Read more king sure that each of the 5 wires on the old element is transferred one by one to the new element. Reverse the process in putting it all together. Turn on the power and walla you've have a new stove. You just save $600 plus.

Exact fit, but read the instructions! Male connectors on element are labeled 1A 1B 2A 2C, very faintly etched in the ceramic. Even though the old and new elements look the same (and I took photos to aid installation), the connector locations are different -- 1A on the old element is where 2B on the new one is, etc. Used included exten ... Read more sion wire for one that would not reach with the new configuration and everything works perfectly.

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you