KEBS276 KitchenAid - Instructions

I tried taking the sensor out, but the plastic coupling behind the oven wall had melted and the melted piece was larger than the opening in the oven wall. I had to use a mini-screwdriver to chip away at the melted coupling before it would fit through the opening. That took forever...but it finally worked and the repair went quickly (15 ... Read more minutes) after that.

Since I had to pay an $80 house call fee, I asked repairman to tell me the model number for the element, called Parts Select, ordered the element myself and saved my weekend of 17 hungry guests.
So, I guess you would say I paid $80 for a diagnosis; I think I really knew the problem and solution all along as I have ordered to-install ... Read more stove top element before.

Removed all terminals and block mounting screws. Repaired one burnt terminal and reassembled. Replacement part was an exact fit and reassembly whnet very well.

Inserted new lint filter...one second! No tools needed. Price excellent!

Took out the old lint filter and put in the new one. Works great

I took the new knob out of the plastic bag and placed it on the oven. The whole process took les than one minute and no tools were needed.

used a utility knife to open the box in which the part was shipped, discarded the old filter and inserted the new one

Just slid new rack in. Looks great! Thanks for having just what I needed.

1993 model oven, built in wall model, so didn't to remove oven for the normal rear access to replace the lamp socket. As someone else posted, replacement can be done from inside the oven -- BUT the socket removal was more complex than just 'twisting it out.' But below worked! (1) Turned off oven power at circuit breaker panel. To facilit ... Read more ate working in the oven compartment, removed oven door (2 screws on back of door), raised the over door almost closed, put 2 large nails through the hinge holes when they lined up. Lifted the door out (heavy ~20-25 lbs) and put aside. (2) Put work light inside oven. (3) unscrew glass socket lens and the bulb). (3) Using inspection mirror, studied the inside of the socket to determine that its lock tab type and locations -> were on left and right sides of the socket. These tabs needed to be bent in, but they were each held out by a small circumferential length of think metal, a tab about 3/16" x 3/8". These small tabs could be moved/positioned by just finger friction, with a little start with a screwdriver tip on their edge! I got an end positioned to put sharp screwdriver under that end, then pried it (bent it) inward a short distance. Enough to use needle-nosed pliers to pull it completely out - came fairly easily. Repeated on other side of socket. (4) Then, with pliers, bent each of the 4 locking tabs inward a short distance, Used sharp tool to get one socket edge lifted a small amount; then use mini-pry bar and screwdriver to gently pry around the socket in steps, working evenly around its edge. At about 3/8", it was free. Lifted it inward gently so as not to damage the insulation of the 2 wires attached to its rear. Noted the direction of the wire tabs was straight up (keep same orientation on new socket). (5) Needle-nosed pliers on each connector to gently work the connectors off their socket tabs. Note one tab is larger than the other. Keep the wires inside the oven compartment. Don't damage the insulation. (6) Pushed the wire connectors onto their respective new socket tabs. Aligned socket with the tabs upward, and inserted it, careful to nurse the wires back into the oven wall hole; press socket into the hole, pushing it in evenly and firmly until flush. (7) Pushed in the new type bulb that came with new Socket. Turned on power, and light came on. (8) screwed on new glass cover. (9) Lifted oven back onto the hinge prongs. (easier with two people to get the prongs aligned and into their door slots.) Worked door left and right to get it to lower down fully. Removed nails, lowered door, and put its 2 screws back on. (10) Poured a glass of wine.

My part was not amazing. What was genuinely cool: I ordered it one day and it was here the next, took out the old and put in the new. Thanks for getting it here so quickly.

After 26 years, the element burned out. I followed the diagrams on this website. Basically, I took out the screws that hold the element in place and carefully pulled the old element forward. The wires had fittings that slipped off the old element (with a little help from the wrench.) When the wires were disconnected, I clipped the adj ... Read more ustable wrench on the one of them to make sure they didn't slip back through the holes in the back of the oven. The old fittings slipped right onto the new element (couple of taps with a small hammer to get them all the way on). Them I slipped the wires back through the holes and put the two small screws in the plate at the back of the element. Quite simple, even for a guy with four thumbs.

REMOVE BACK COVER. UN PLUG, REMOVE TWO SCREWS IN SIDE OVEN, PULL OUT , REPLACE, REATTACH, FIXED CODE F-3

took out old and placed in new

Simple. But beware changing just the bulb when the gasket is not secure.

Turned off breaker, verified that the breaker controlled the oven and was actually off.
This is important since you can still get a shock from leaks in the neutral side that may surprize you if you ground one side. Also some breakers can be mislabeled on older homes.
I removed the two screws holding the element to the back of th ... Read more e oven phillips #1 screw driver.
I carefully guided the wires and attached terminals out of the recess until
I had about 5 Inches of wire inside the oven exposed. Just be patient and careful, they will come out.
I then unpluged the wires from the old element and attached a binder clip to the ends so they could not slip back into the oven shell. Clothes pins are also a good choice or some duct tape.
I thoroughly cleaned the oven.
I then installed the wire terminals to the new element and reversed the removal procedure.
I then verified function and temperature of the oven settings.
It took me 10 minutes not including oven cleaning time.