KEBS14 KitchenAid Wall Oven - Instructions

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Unwrapped the package, plugged the probe into the oven, stuck the other end into the chicken.

Remove oven from wall, remove top and back covers.Remove old fan assembly. The new assembly fit right in and works great.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

Took the door off, removed the screws, took door cover off, cleaned the other two pieces of glass and the new one, and then reassembled. I set the screws aside so I put them back in the same holes. I never want to take the chance of a possible cross threaded screw not going back into the same hole. ... Read more Note:Now is a good time to clean edges with oven cleaner before reassembly.

Had to screw off old terminal block & screw on new one

Removed double oven from cabinet after removing the doors, placing it on a milk crate, needs two people, turned it slightly to access the rear panels, removed panels and lower of the 2 motors and installed new motor, replaced all panels. I now have to check to make sure it is turned on it is so quiet! We lived with this noise so long beca ... Read more use the appliance repair people said it was very expensive, about $400.00 to replace the motor, we did it for under $100.00 !!

FIRST: I Shut off the circuit breaker to the oven. Then: 1. Removed convection-fan cover (it was partially blocking the bake-element screws). 2. Unscrewed 2 bake-element screws. 3. Pulled old bake element forward to expose connectors. 4. Disconnected both connectors and discarded the old element. 5.Connected the new element and pushed i ... Read more t in so that plate was flush against the back of the oven. 6. Re-installed the 2 element screws. 7. Re-installed convection-fan cover. LASTLY: Turned on the circuit breaker to the oven and baked a cake! IMPORTANT: The original screws can be very, very tight. When removing them, be sure to use a socket wrench or other tool that gets a firm grip on the hex heads, or you could round the corners of the heads, permanently damaging the screws.

turned breaker switch off. unscrewed the oven from the cabinet. lifted the oven out of the cabinet (heavy & awkward, needed an extra pair of hands). removed back panel. replaced fuse. reassembled everything. this is the second time i've had to replace the thermo fuse (oven blows the fuse when set to clean). first time i replaced the fuse ... Read more it took about two hours. second time it about an hour.

followed the brief instuctions you provided easy as pie

Did not want to remove the pin from the new hinges, so found a proper rod and cut off two half inch pins to use in removing the door. followed the manual instructions. Took all of the screws out but did not notice that the four inside face screws were machine screws while all others were sheet metal screws. Had a little difficulty in get ... Read more ting the four machine screws to engage the bottom holes of the new hinges. Reinstalled the door and all works fine. It is too bad that we could not purchase just a new hinge spring instead of the entire unit. It is kind of a waste. I suspect that self cleaning ovens generate a very high heat which eventually weakens the hinge. The upper oven will likely fail in the future, but at least I know how to repair it.

First of all I would like to say how prompt the delivery of my oven glass was. I ordered it Thurs & it came on Sat ~ 2 days thats amazing! Ordering my glass was easy & the representitive that helped me was very nice & the price was great! My husband repaired it in about 20 minutes - very easy to istall the glass & very cost effective repa ... Read more iring it ourselves rather than having a repair man come out! Thanks Part Select I will recommend you to all out fam & friends most definetly!

The repair went well & the part came in on time for thanksgiving thank you

I followed the instructions given and it was very easy

Not difficult, but there are several layers of glass, metal, and insulation inside this door. Keep track of where the screws go and have room to lay out all the layers. You'll reach the cracked inner glass last.