EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KCCC151B0 KitchenAid Trash Compactor - Instructions

All Instructions for the KCCC151B0
76 - 90 of 118

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
the compactor was stuck in the down position
  • Rod from Quincy, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Had to first raise the screw plate that compacts the garbage. Then had to turn the compactor over and remove screws holding the bottom plate on in order to get to the gears. Once that was done I removed the worn gears and the chain drive and replaced with the new gears and the chain. Put the unit back together and works like a new one. A $35 dollar fix for a unit that sells for around $900 today. Thanks to partslect for being able to help me with the parts needed. Not only did I save on a new unit but by doing this myself I saved around $100 in labor charges.
Was this helpful?
Thank you for voting!
Unit cycled when on switch operated and would not stop until Off switch was activated.
  • Gerald from Wickenburg, AZ
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
Replaced the limit switch. This did not alter the problem. Took off the On/Off/Start switch and dissasembled. I found the the Start switch was stuck in the on position. I reassembled the switch mechanism assuring that the Red "ON" indicator moldings were correctly positioned and reassembled everything. The Compactor now works properl y. Need to add "Check the Start switch" to diagnosis.
Was this helpful?
Thank you for voting!
Ram stuck in down poaition
  • Candace from Ocala, FL
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Replaced drive gears.They arrived in a kit from Parts Select with instructions.They fit perfectly and the compactor works like new.
Was this helpful?
Thank you for voting!
Compactor would travel down at the bottom of its range would just rumble like a Jack hammer until I unplugged
  • Richard from Stow, MA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers, Socket set
Looking at the information I found online it was either one of 2 things the directional switch was bad, or the drive gear was broken. I replaced the directional switch 1st since that was the easiest and that did not solve my problem. I put it all back together and thought about it for a little while. After a couple of days. It occurre d to me that I could see the ramrod's spinning as the plunger goes down, then when the plunger reached as far as it would go. The ramrod's would stop spinning. I reasoned that the problem had to be somewhere between the motor and those rods when I opened up the bottom of the trash compactor, Iran the cycle again and I could see that the drive gear was still spinning, but the chains to the ramrod's were not spinning. Once I saw that I realized that the sprocket that was attached to the drive gear had broken. The sprocket is metal and the drive gear is plastic and they fit together perfectly, but through age or stress. The plastic have become rounded and no longer fit perfect on that nut when you applied a good deal of pressure. I didn't have the tool that I needed to replace the small drive year. I think you need some kind of a punch to get that pin out. So I left that one in place loosened the nuts that hold the motor in place to create some slack in the chain chain came off the new drive gear one on. I tightened the motor back up in the correct position is reassembled everything and it's working perfect again.
Was this helpful?
Thank you for voting!
The compactor was loaded with too many wine bottles
  • james from Milton, MA
  • Easy
  • 15 - 30 mins
  • Screw drivers
At best it is advisable to load just one at a time and covered with newspaper etc., In this case someone put in three bottles with out covering with heavy newspaper etc.and for some reason one rode out and to the side. Crushing the side of the metal trash container. This pinned the container against the side of the compactor body and behi nd the front rails. Using a lot of pulling and some nifty pry bars and two hours of prying and squeezing we got the container out( see attached photo )The replacement container was ordered on a Sunday night and arrived Tuesday morning. Removal of the existing front panel ,foot pedal and door switch was easy and installation on to the replacement container was a breeze with a little orientation required to line up the switch and pedal in the right configuration. 20 min tops and that was with five kids helping ;)
Was this helpful?
Thank you for voting!
I changed the front panels from the original beige to stainless steel
  • Walter from San Rafael, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The repair was a breeze, a piece of cake, a walk in the park, a day at the beach. The part arrived quickly and installation was fast and simple. A week earlier I had the misfortune of ordering these parts from another supplier. One of the parts obviously was not correct, so I called customer service. Although the operator was polite, she insisted that the part I received was the right one (even though it was 2 inches too narrow). I looked up the part at PartSelect.com and ordered it. It arrived the following day, and fit perfectly. Thanks, PartSelect.com.
Was this helpful?
Thank you for voting!
stripped pinion gear
  • jeff from lincoln, AR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I took the hex screws out with a nut driver and then punched out the role pin in the pinion gear (the little gear) and replaced it along with the large gear, less than 15 minutes. I was surprised how fast (day and a half) the parts were here.
Was this helpful?
Thank you for voting!
20+ plactic gears striped them selfs who da thunk
  • Fred from Belmont, NH
  • Really Easy
  • Less than 15 mins
  • Nutdriver
took longer to pull it out and put it backunder the counter then to pull the panel take the chane gear & drive gear off and put it back together
Was this helpful?
Thank you for voting!
compactor was crushing the bag holder
  • Myles from Jackson, NH
  • Really Easy
  • Less than 15 mins
easy ... got the new bag holder and replaced old one. the impressive part of the process is how easy it was to get the part info from partselect website. could have spun my wheels a lot without that.
Was this helpful?
Thank you for voting!
the switch did not click off
  • janie from mcHenry, IL
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
very easy to fix. all it took was pulling the compactor out to unplug,take off the removable front nob, unscrew two screws located just below the front panel.using needle nose pliers to remove the actual switch, unplug the wires conected to the switch and put the new one on the same way. It almost took me longer to write this discription than it took to fix!
Was this helpful?
Thank you for voting!
The panel got bent
  • Steven from Elk Creek, CA
  • Really Easy
  • Less than 15 mins
Took the bent one out, put the new one in. The repair was not the story, the story was that we ordered the part on Monday afternoon and it was delivered on Tuesday! And the shipping was less than $8.00. Fresno to Elk Creek in less than 24 hours for that price was amazing!
Was this helpful?
Thank you for voting!
compactor will not stop when compaction complete on top cycle
  • BRUCE from CASPER, WY
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
take 2 screws out on top cover with key switch. remove two screw holding directional switch. remove wires, one at a time, and place on the new switch. put new switch in place with two screws. put front cover on with two screws and test. works like a charm.
Was this helpful?
Thank you for voting!
my compactor container was badly worn out
  • Richard from East Wenatchee, WA
  • Really Easy
  • 1- 2 hours
  • Screw drivers, Socket set
All I really needed to do was to take the front facing off and put on the new container, but I took the opportunity to do a complete overhaul and cleaning. It now work like a new compactor.
Was this helpful?
Thank you for voting!
Large ring gear - delrin - split in two
  • Chris from Burlington, CT
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
Laid appliance on side - removed top sheet metal cover and bottom sheet metal cover. Broken delrin ring gear was on bottom of bottom cover (housing). Gear had broken off of its hub, which also was the sprocket chain drive for both acme screws driving the compactor platten. Motor had to be loosened so that the chain could be removed f rom the old sprocket hub, and the new delrin ring gear - with new sprocket hub attached - could be mounted on its fixed spindle. With new delrin gear/chain sprocket mounted, the motor had to be spaced and tightened to allow 0.010 inch lash between the gears. The only instructions included with the new gear was how to do this - by placing a piece of paper in between the pinion gear on the motor, and the new ring gear, and then tightening the motor into place. This was done, the sheet metal covers were re-installed, and the compactor works just fine. There is a design flaw in the original (KitchenAid) engineering of the gear, however, and I expect that in the next four years this will probably happen again.
Was this helpful?
Thank you for voting!
Trash compactor would not turn off at end of cycle and made a grinding noise and some vibration
  • Ronald from Brentwood, TN
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
I removed the unit from under the kitchen counter by first pulling the trash drawer all the way out and lifting it out of the track and setting it out on the floor. I then slowly pulled the compacting unit out and unplugged the cord from the electrical outlet. With the entire unit out in the floor I took a nut driver and removed the screw s from the top plate and the screws from both sides at the bottom of the front housing. This allowed access to the directional switch. Two screws on the right side of the switch have to be removed to remove the switch along with two holding plates on the left side of the switch. The switch can then be accesses for removal. Several wires are attached to the switch and should be removed one at a time and installed to the identical identical location on the new switch. The new switch can then be installed by aligning the holes and reinstalling the holding plates. When this is done the front frame and top plate can be replaced with the nut screws. Plug back into the electrical outlet and see if it works. In this case it did exactly what it was doing before I started. So either I did not reinstall the directional switch properly or I am in the one percent rather than the 99 percent that should successfully solve the problem as suggested in the trouble shooting guide. I will now recheck the installation of the directional switch nd then check the bottom of the unit to see if the gears or chain drive are broken .
Was this helpful?
Thank you for voting!
All Instructions for the KCCC151B0
76 - 90 of 118