EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

KCCC151B0 KitchenAid Trash Compactor - Instructions

All Instructions for the KCCC151B0
61 - 75 of 118

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ram quit moving
0 of 1 people found this instruction helpful.
  • Hal from Granada Hills, CA
  • Easy
  • 30 - 60 mins
  • Nutdriver
Removed bottom and replaced gears
Was this helpful?
Thank you for voting!
Compactor ram was stuck in the down position and door would not open
0 of 1 people found this instruction helpful.
  • Michael from South Boston, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
After inspecting to make sure the actuator was functional and that power to the unit was not an issue I was able to find that one the drive gears cracked in half and made the compactor inoperable. It was easy to remove the bottom casing with a nut driver. This casing covered the drive gear which operated the ram. After slightly loosening the gear mounts and I was able to replace center gear and re-attach gear chain and re-tighten. Then replace bottom casing and the compactor was back in action. Huge savings!
Was this helpful?
Thank you for voting!
Broken Drive Gear
1 of 4 people found this instruction helpful.
  • Michael from Painted Post, NY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Removed the gear cover at the bottom of the compactor. Loosened the slack on the chain. Replaced the gear drive. Replaced the gear cover. Worked like new. No major obstacles.
Was this helpful?
Thank you for voting!
Both outside door handles turned very beige
23 of 76 people found this instruction helpful.
  • Howard from Boynton Beach, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol oring refer handles. Thank you
Was this helpful?
Thank you for voting!
roller bearing for trash bin was damaged and would not allow canister to roll
6 of 32 people found this instruction helpful.
  • roberto from keller, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Wrench (Adjustable)
the bearing were the perfect match and instructions helpful. sysem is rolling smoothly
Was this helpful?
Thank you for voting!
Broken drive gears
  • THOMAS from DENNISPORT, MA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Took out old gears replaced with new very easy with your dirictions.
Was this helpful?
Thank you for voting!
Large plastic gear cracked in half. Compactor was stuck in the compact postition
  • Mike from Campbell, CA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
replaced the large gear and put it back together.
Was this helpful?
Thank you for voting!
plastic gear broke in half
  • Richard from WAYLAND, MI
  • A Bit Difficult
  • 30 - 60 mins
Same problem as described previously on this site. Pulled unit out and replaced the gear as described. Thanks for the info - would have been tough with out it.
Was this helpful?
Thank you for voting!
Drive motor would not turn off after completing cycle
  • William from Jacksonville, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Pull unit from under counter (Held in place with 2 screws) Use nut driver to remove top and front panel. (I didn't remove the control panel from the front panel which probably made access more difficult) Locate the directional switch near the top of the unit and remove two screws, being careful not to lose a small metal plate into which the screws thread (similar to a Tinneman nut). I moved the wires one at a time from the old switch to the new as I am color blind and have trouble with wire colors. Fit the new switch in place, being sure the switch lever is positioned against the metal tab that operates it. Screw the switch in place and then reassemble the compactor.
Was this helpful?
Thank you for voting!
Broken plastic drive gear
  • Charles from Goshen, KY
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Very simple, changed the gear, adjusted the drive and tested. Very straight forward.
Was this helpful?
Thank you for voting!
Primary Power Transfer Gear Split in Half
  • Robert from Willow Creek, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Compactor ram was stuck in the down position after hearing a loud bang during a compacting cycle. Removed outer compactor casing to determine cause, only to find gear housing underneath the compactor that contained drive chain and gear assembly. Primary gear had split neatly in half. Determined the appropriate part needed with partsele ct part finder (of course, an entire kit, and not just the gear), had part shipped and had compactor repaired in three days. The actual repair and reassembly of the compactor took less than a half-hour. Consisted of removing chain tension from gear hub by loosening four sheet metal screws holding motor assembly, removing circlip and old gear hub from chain and shaft, replacing gear hub with new part, lubricating the gear mechanism, and reinstalling in reverse order.
Was this helpful?
Thank you for voting!
Ram was stuck in the down position
  • Joseph N from Wheaton, IL
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
changed out the big gear that was broken
Was this helpful?
Thank you for voting!
Directional Switch lever broke
  • Dick from Penn Valley, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The part was suppose to come with instructions, but did not. However, it was easy after reading the comments on-line, and discovering that the front cover had to be removed in order to expose the whole switch and wires. I did drop one of the mounting screws down the front of the compactor and was not able to recover it. So, I had to ma ke a trip to the hardware store for a replacement. They couldn't match the remaining screw but I found 2 similar ones with lock washers and nuts that worked just fine. I saved a $90 service charge and probably double the cost of the switch by doing it myself.
Was this helpful?
Thank you for voting!
compactor wouldn't compact
  • Tena from Parker, CO
  • Easy
  • 15 - 30 mins
  • Screw drivers
bought new gears, pulled it out and replaced the gears. wasn't very hard. I did expect a jenn-air to be better built (plastic gears really!) but for 30 bucks it is all better.
Was this helpful?
Thank you for voting!
broken rotary switch
  • john from red bluff, CA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
remove drawer remove two phillip screws lift off front panel remove wiring and plug into new switch.slide switch through the hole in panel install nut reinstall panel screws and drawer job done.
Was this helpful?
Thank you for voting!
All Instructions for the KCCC151B0
61 - 75 of 118