KBHC KitchenAid Microwave Oven Combo - Instructions

Replaced the glass tray

Easily replaced after received the product from Part Select. Very satisfied.

found the part no. and ordered it. it was delivered fast and efficient.
tracking was also helpful.
thanks

took the plate out of the shipping box, inserted it in the microwave

no repair needed - ordered part, came within 3 days - very satisfied

Well the repair went Ok. The probelm happen on the following Monday. You see I ordered this part over the phone because I had to make sure it would arrive in time for Thanksgiving.

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Turned off power. Slid the built-in microwave out, started taking screws out, couldn't find any manual for this so just took apart more than was needed. Replaced front keypad, replugged into motherboard and reassembled. Pushed back into cabinet and turned on power. Repairman wanted $700 to fix it, part was about $350.00

Removed the door frame by breaking it as there was no obivious way to get at a couple of the screws. Replaced the broken right spring as it was the original problem. Replaced the door frame by drilling a hole thru the exhaust tube of the regular oven mounted below the microwave.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discol ... Read more oring refer handles. Thank you

To access the springs you have to take the outer door off. This is the stainless steel panel with the glass panel. On the inside of the door on the plastic panel near the top are two small screws. You must remove them. BEWARE the screws and two clips at the bottom of the door are the ONLY things holding the door on. I removed the two scre ... Read more ws and the $160.00 door fell on the floor and broke. After ordering a new door I went back to replacing the springs ( one broke but I ordered both of them ). To get at the springs you must remove the plastic panel. To do this you must remove the plastic vent panel between the microwave and the oven ( 4 screws ). There are two screws holding the plastic piece on at the bottom. The one on the right is easy to get to, the one on the left is above the metal snorkel like vent. Inside the vent is a screw I removed it with a pair of pliers ( very tedious ). With the screw out move the vent to the right to access the second screw then remove plastic the springs go right in with no problem. Reverse procedure and you're done. Remember two screws on outer door and then it drops.

Had to screw off old terminal block & screw on new one

Broke again - same spring - 4th time, maybe 10 years old. Last break/fix was October 2010, so got just a little over 2 years out of a new one. Only me and my wife, so not like it's 5 wild kids and their friends attacking the door. Just a bad design, it seems. But, see my earlier instructions - every time this happens, I order new part ... Read more , print out my old instructions, wait a day or so for part to arrive (really quick this time - asked for 3-5 days delivery, got part in just 1!!! Way to go PartSelect!!!!), then repair in 25-30 min.

I broke the outer window glass because the instructions didn't inform me that once a couple screws are removed the outer door glass can and will fall from the rest of the door piece and shatter on the ground! After paying $180 dollars to get the replacement I gingerly continued to dismantle the rest of the door to get to the torsion sprin ... Read more gs. Another issue with dis and Reassembly is the lower oven chassis heat exhaust vent is directly below one of the screws that holds the door together. I drilled a 1/4 hole that allowed the screwdriver to pass through the sheet metal exhaust vent! Plastic can and will crack, screws can and will get stripped and it would be wise to have an assistant to help hold it together during reassembly. Otherwise it's really easy and all you need is a Phillips screw driver! LOL

After I got over being upset about smashing the door into a million pieces I just looked for the part on your website and ordered it. It was delivered in four days and the installation was really quite easy. I just slid it into place and screwed it back on to the door. It took about 5 minutes or less! It could not have been an simpler. ... Read more ..