JRP034J4 General Electric Range - Instructions

Unscrewed the broken element from the back of the inside of the oven, then unscrewed the connected wires from the element and did the reverse with the new element. Viola.

Before touching anything, however, I made sure the oven was in the off position and also went to the house circuit breaker box and flipped OFF the appropriat ... Read more e circuit breaker(s). There were two - one for the element and another for the rest of the controls.

When everything was in place, I turned the power back on and turned on the oven and was cooking again. We had Prime Rib for Easter.

I have to admit that I tried to remove the element myself but I did not have the right tool for the last two screws. If I did it would have been very easy. I ordered the part and had someone else put it in so I cheated.

My petite 69 yr old wife replace element in about 15 minutes with no problem..Also product arrived within a short time frame and your online instructions were accurate. Thanks

Easy! Removed the screws, took out the damaged element, reversed the process with the the new element. I called in my order on Monday and Wednesday evening the oven was repaired! It doesn't get any better than that. Thanks for the great service.

Took out old element with screw driver and replaced new element with screw driver, very simple.
We were so happy with the customer service, had the new element the very next morning. Thank you.

replaced with a new part . Thanks for all your assistance in getting the correct part

remove two screws from back of oven holding element to back of oven. Pull out gently, remove two screws holding wire connections(power wires) throw away old element. Place new element into oven. Reconnect element to power wires using screws. Push element back into back of oven. Replace screws holding element in place. Turn oven on to chec ... Read more k for proper connections.

You website was quite easy to use and we found the part really quickly. After we ordered it, it was delivered within 5 days and was easy to install. I was a happy camper to have my oven back which I use a lot. Thanks for the quick delivery and information. Candi

The removal- replacement problem basically involves the shortness of the connector wires to the terminals. Because the burner is close to the top there is little room to use a screwdriver. The old unit used metal screws. The new came with open threaded holes in the terminals with two threaded screws. Used a small 1/4" ratchet which wor ... Read more ked OK, but had to carefully bend the ends of the terminals to allow me to lower the element to an angle that would all room for ratchet action. (All design engineers should first have to work in maintenance before going to drawing board!)

S. Cooke, Houston Texas

On Thanksgiving Day, we were making a pecan pie. The lower oven started to smoke and flame. We quickly turned off the oven, removed the pie, and noticed that half of the lower burner element had turned into cinders. I copied down the part number and serial number of the oven, went to Google, and found the replacement part that I needed ... Read more . Once the oven had cooled down, I turned off the circuit braker for the oven and tried to remove the burned out heating element. The good news was that I could remove it with my SAE socket set. I then ordered the part on line, knowing with confidence that I could do the replacement myself.
The part arrived one day after I got the email that the part had shipped. That is great service!
I waited till the next day to do the repair since I needed to have the right tools lined up and I needed to wear clothes that might get dirty when working deep inside the oven. A flashlight and a socket set with a 1/4 inch drive were the main tools I needed to do the electrical connections and the oven connection. I also used a blunt putty knife to clean out some of the goo in the oven.
After the repair, I turned the circuit breaker back on and placed a separate oven thermometer into the oven for the first test. The oven worked just fine at 250, 350, and 450 degree settings. Wife is now happy!

Throughout, I took care to not rest my full weight on oven door, although it's hard to work with arms extended. Shut off power to oven at outside circuit breaker, removed both racks, placed trouble light on open oven door at left to illuminate back of oven. Tilted element up to get at bolts. Used 1/4" socket set to remove two hex bolts ho ... Read more lding burned-out element's plate to back of oven, pulled it out 3" to expose wire connectors. Held connectors still with pliers in left hand (to not bend wires) while loosening/removing connector bolts with socket set in right hand. Took effort to loosen. Removed element. Wiped oven floor clean. Positioned new bake element in same place, again held connectors still with pliers (left hand) and tightened wire connector bolts with socket set (right hand), pushed element back to original element's position. New element came with screws, not bolts, so used magnetic Philips screwdriver to get screws lined up (tricky), tighten new element's plate to oven's back wall. Removed trouble light, restored power, set closed oven for "bake" and "350 degrees." Element glowed hot in 1 1/2 minutes, ta-daah!

took the element screws off, a little bit dificult to fine the small wrench socket to disengage. I had to have my husband do it because I have too short arms.
I can't believe how much money we saved., the part was there within two days and installed, for a total of 52.00 including next day Fed ex.
Feel good about the whole ... Read more expierence.

First turned off the power to the oven then removed two screws holding element in place. Pulled it out a couple inches disconnected the two wires. Then connected two wires to the new element pushed it back into two place and reinstalled screws that hold element in place. Really easy about 15-20 minutes to complete

Took the old one out and replaced with the new one. It was just awkward to get at.

New element arrived in a couple of days! We turned off breaker to oven, removed the old one which only involved two screws. Then we had to connect new one and re-attach metal square, only tricky part was getting the metal square positioned correctly but that was really not hard, just made sure insulation was covered and plate went back in ... Read more same position. If we had called a eepair company it would have taken a week or more and probably been expensive!