JMV9196CS2 Whirlpool Microwave Oven Combo - Instructions

took it out of box wooolaaa fixed thanks fast shipping too...

It was a very simple and easy fix, no tools needed. First, open the door to the microwave/oven and remove the glass plate and the plastic plate guide. Next, locate the whole in the center. Using your finger, find the drive coupling pin that sits just below the opening (half circle shape). Align the bottom of the drive coupling with the me ... Read more tal pin and press down. Replace the plate guide and plate. The grooves in the bottom of the glass plate should be aligned with the shape of the drive coupling. Test by setting microwave/oven to 30 seconds and watch for proper turning and alignment.

Based on other similar posted repairs, I purchased the bottom switch. Upon removing the control panel to replace the switch, I found the blue 22 gauge wire was broken at the spade terminal. This wire had been crimped to the terminal along with a 14 gauge wire. Apparently the force to crimp the thicker wire weakened the smaller wire at ... Read more the terminal. I stripped the end of the small blue wire and reattached it to the thicker wire using a solder iron and solder. The repair fixed the problem.

I removed the microwave to install a back splash and found the support edge on the backplate had broken off and was missing. I searched for parts for the microwave and found them on PartsSelect.com. Easy to order, and was shipped promptly.

Once the part arrived, install was simple, lining up the existing holes. The only hard p ... Read more art was setting the microwave up on the bracket due to the weight and awkwardness of the microwave.

Overall a very simple repair.

After removing the over-the-range unit (no small feat!) I had to figure out how to open the case (good puzzle!). Capacitor had already discharged, so it was very easy to reach in, pop the old fuse and install the new one! As per your advice, I found out I was a "28%-er"! Upon re-installation, the microwave "sprang to life"!! Thanks, "P ... Read more art Select"!! I was already shopping around for a new machine! (Now if you could only tell me an easier way to re-mount this heavy beast over the stove!!!)

On top front of the microwave are two Philip's head screws holding the rail on. Remove these screws and the rail snap out the old filter (noting the dark side down) then snapping the new filter in. Replace rail. 10 to 15 minute task.

I took off the glass panel underneath the microwave and replaced the 2 bulbs in less than 3 minutes by myself with only a phillips head screwdriver. I was very pleased with the service I received and more pleased with myself that I did not have to call in a repair man.

Removed the face plate above the door (2 Phillips screws.) Removed existing filter and replaced with the new one purchased. Reinstalled the face plate.

when I opened the back cover of microwave, the diode was kind of blackish blown, since there was light bulb and fan were still working, i thought it could be problem with any one of the components like; magnatron or capacitor or diode, so first replaced the diode and mica at the end of the magnatron duct, there was problem with door switc ... Read more h as well. i fixed that too. Now it is working. It cooks bit faster, Wondering why?

This is an under the counter microwave. Simply removed the two screws holidng the vent grille on top of the unit, lift out the old charcoal filter, clean the vent fan exit surfaces then replace the filter and put the vent grille back. Be careful to not drop either of the two screws after one is installed as you will have to take the gri ... Read more ll off and start the screw installation again unless you have a magnetic to retrieve the dropped screw. An easy five minutes at most to change.

I simply lifted out the glass rotating plate and inserted the new support. How complicated can that be?!!!!!!!!!!!!!!!!!!!!!!!!!!!

I was sent the wrong fuse by you. I had to procure a fuse in another manner. Very disappointing. The repair was simple. It just took longer because of the failure to send the correct fuse.

took it to Buttermore appliance in Auburn Indiana and he changed the fan and added another fuse

Took the front off and behind a plate was the fuse, so I replaced it for what good that did!!!

Replaced filter which came inrecord time.