- Home
- JMS08BD1AD
- Instructions
JMS08BD1AD General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The terminal burner block was burned out, and surface plate not heating.
7 of 9 people
found this instruction helpful.
-
Carol A. from Orlando, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
My husband removed all the old terminal block and element, and put the new one in. It was very easy. Thank you for the instructions which were included.
Other Parts Used:
Was this helpful?
Thank you for voting!
Control on one burner would heat on high only, not lower heat level
12 of 25 people
found this instruction helpful.
-
William from Hammondsport, NY
- A Bit Difficult
- More than 2 hours
-
Pliers, Screw drivers
Bought new version of control element (parts no longer available for the old one) and luckily had a sheet with the oven describing how to disassemble the cook top from the range to get to the old control. After removing the top and installing the new control element, followed the instructions backwards and reassembled the range. Total job
... Read more
took about 4 hours. A real serviceman could probably have done it in 2 Hrs.
Read less
Was this helpful?
Thank you for voting!
element burned out
6 of 7 people
found this instruction helpful.
-
John from Durham, NC
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
It's so simple most people could mannage the repair. Turn oven off. Remove oven door and shelves. Use a nut driver to remove mounting screws. Pliers to pull quick connect terminated wires off element terminals. Use pliers to push connectors onto new element,wires may connect to either terminal. Nut driver for screws to mechanically mount
... Read more
new element. Replace shelves and door. First time element gets hot it will burn off oils and dirt, not a problem but do it now not later.
Read less
Was this helpful?
Thank you for voting!
Replace the heating coil in convection oven
5 of 6 people
found this instruction helpful.
-
Victoria from San Jose, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
[1] squirted LiquidWrench on the 4 screws holding the convection fanblade rear cover in place. Used a socket and rachet to remove screws; the loosener really helped after 10+ years.
[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back ... Read more into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.
[2] the broken heating element was easy to remove. The two spade connectors however didn't have much free length;these wires wanted to retreat back ... Read more into the rear oven wall.
[3] So i put a small binder clip from my desk supplies on each spade end, this left the connectors where I could grab them.
[4]I used needle-nose pliers to firmly crimp the the spade connectors onto the new heating element; couldn't have made a firm placement with fingertip pressure alone.
[5] I cleaned the oven door hinge area, oven bulb area, and other hard to reach spots with Simple Green and wipes.
Read less
Was this helpful?
Thank you for voting!
TOP OVEN BROILER ELEMENT BURNED OUT & BROKE
5 of 6 people
found this instruction helpful.
-
HIDDEN HILLS from TONASKET, WA
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
1) TURNED OFF THE POWER TO THE OVEN. 2) REMOVED THE TOP DOOR AND RACKS. 3) REMOVED THE 2- 1/4 HEAD HEX NUTS AND PULLED THE ELEMENT FORWARD ENOUGH TO EXPOSE THE ELECTRICAL CLIPS TO THE ELEMENT. REMOVED THE CLIPS WITH A PAIR OF NEEDLE NOSE AS ADDED GRIP. 4) PUT THE WIRE CLIPS ON THE NEW ELEMENT A
... Read more
ND REVERSED THE ABOVE PROCEDURES.
Read less
Was this helpful?
Thank you for voting!
I had to replace my drip pans as well as the heating elements on all four burners
4 of 4 people
found this instruction helpful.
-
Cindy from Moreno Valley, CA
- Very Easy
- Less than 15 mins
Very simple to replace, pull off the old element and push in the new one. Not only was it super easy, part select was so easy to work with. I had placed the order wrong, and immediately called customer service. They cancelled my order and placed the new one, refunding my money within 2 business days for the wrong order. Courteous, friendl
... Read more
y and prompt. I would highly recommend them! Oh, I forgot to mention that the parts actually fit perfectly, unlike drip pans bought elsewhere. Thank you, Sincerely, Cindy
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Front Large Most Powerful Burner's Block had broken so it didn't heat
4 of 4 people
found this instruction helpful.
-
Martin from plainfield, CT
- Really Easy
- 30 - 60 mins
-
Pliers
This electric stove has a lift up top which I lifted to get at the block and follow the wire back to the terminal at the back of the the stove. I removed the 5 small lag screws holding the back in place, removed the backing followed the wires back to where they connected in the Stove On/Off Control, disconnected the two wires from the co
... Read more
ntrol and then laid the new part in place rethreading and reconnecting the wires. I reinstalled the block and ran a test to ensure the burner operated correctly. After successful testing I disconnect the old block holder by removing the small lag screw, replace it with a new one that came with the replacement terminal block. I then inserted the block into the new holder carefully rolled up the excess wire and wrapped it in a couple of places with electrical tape and also secured it to the side of the stove, out of the way of operation with electrical tape, put the top down, plugged it back in and put it back in place. All told the repair took about 40 minutes. I was impressed with the speed of delivery, the quality of the product, the instructions for installation and the added bonus of getting a terminal block holder as part of the repair kit! Thank You for making me look like a genius!
Read less
Was this helpful?
Thank you for voting!
terminal was broken due to maney uses
4 of 5 people
found this instruction helpful.
-
Emmett J from Winchester, VA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
unscrew the terminal block,pulled the old wires out,installed the new wires installed the new block
Was this helpful?
Thank you for voting!
Surface Burners were very slow.
4 of 5 people
found this instruction helpful.
-
Fisher from Fort Collins, CO
- Really Easy
- Less than 15 mins
Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com
Other Parts Used:
Was this helpful?
Thank you for voting!
unit burnt out no broiler
7 of 14 people
found this instruction helpful.
-
Becky from Piedmont, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
took old unit and measured it part select made it easy for me ordered new unit and installed easily and quick thanks to quick service and shipping
Was this helpful?
Thank you for voting!
The burner bowls were burnt through and nasty looking.
3 of 3 people
found this instruction helpful.
-
Isabel from The Colony, TX
- Really Easy
- Less than 15 mins
I carefully removed the burners, removed the bowls and replaced them with the new ones. Easy as pie!
Other Parts Used:
Was this helpful?
Thank you for voting!
Two sockets for electric elements and their end terminals were badly burned.
4 of 6 people
found this instruction helpful.
-
Marco from Santa Barbara, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
0) Take the back cover of the range off.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For eac ... Read more h unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
1) Carefully noted how the wires and the sockets were connected.
2) Visually checked that the new parts were practically identical old ones.
3) Put together the new sockets from the parts in the kit.
4) disconnect the old sockets and put the new sockets in place.
5) For eac ... Read more h unit disconnect one old wire at the time and connect the new wire. Repeat the same for second wire.
6) Neatly bunch together the rest of the wires with electrical tape. Do not cut the wires!
That's it! It took about 20-30 minutes.
Read less
Was this helpful?
Thank you for voting!
drip pans had become old and burned out
3 of 4 people
found this instruction helpful.
-
aiden from philadelphia, PA
- Really Easy
- 30 - 60 mins
Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy
Other Parts Used:
Was this helpful?
Thank you for voting!
In My Carelessness, I Ruined The Burners On My Stove Using A Really Abrasive Cleaner, And Had To Replace Them With New Ones. My Stove Looks Brand New, And I Feel Better!!
3 of 4 people
found this instruction helpful.
-
Diane from Fraser, MI
- Really Easy
- Less than 15 mins
Nothing to it. Took off the old ones and put on the new! Tada - new stove!!
Other Parts Used:
Was this helpful?
Thank you for voting!
Surface element was corroded.
3 of 4 people
found this instruction helpful.
-
Paul from Southern Pines, NC
- Really Easy
- Less than 15 mins
Removed existing surface element and replaced with new element.
P.S.
Part Select service was excellent.
P.S.
Part Select service was excellent.
Was this helpful?
Thank you for voting!