JMS0701 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom Bake Element had burnt into/split
1 person
found this instruction helpful.
-
Miranda from UNION GROVE, NC
- Really Easy
- Less than 15 mins
-
Socket set
Very easy and simple/ After making sure power supply was off, removed socket screws in back plate of element, slid old element out, attached new element and replaced/tightened socket screws on plate and new element. Power on, oven on .. heated quickly and nicely. Used oven several times since ... no problems.
Was this helpful?
Thank you for voting!
Really old range. Broken bake element in oven.
1 person
found this instruction helpful.
-
Kathleen from Grand Rapids, MI
- Very Easy
- Less than 15 mins
Turned off power. Removed old broken one installed new one in minutes. Turned power on and tested it out. If this 60 something lady can do it, you can too.
Was this helpful?
Thank you for voting!
Oven heating element failed
1 person
found this instruction helpful.
-
megrew, from COLORADO SPGS, CO
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating eleme
... Read more
nt. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!
Read less
Was this helpful?
Thank you for voting!
Bake element burned out
1 person
found this instruction helpful.
-
Lavona from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to te
... Read more
st it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*
Read less
Was this helpful?
Thank you for voting!
No problems
1 person
found this instruction helpful.
-
Darlene from NORTH AUGUSTA, SC
- Really Easy
- Less than 15 mins
lift eye slide in bowl and trim ring, put the eye back down,
Other Parts Used:
Was this helpful?
Thank you for voting!
Bottom oven heating element was out
1 person
found this instruction helpful.
-
John from FALL RIVER, MA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this helpful?
Thank you for voting!
No heat from bake element
1 person
found this instruction helpful.
-
Roberta from Southampton, NJ
- Really Easy
- Less than 15 mins
-
Socket set
Ordered part, took old bake element out, installed new bake element. It was real easy.
Was this helpful?
Thank you for voting!
The bottom bake element burned out.
1 person
found this instruction helpful.
-
Pauline from DECATUR, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.
Was this helpful?
Thank you for voting!
replace broiler element
1 person
found this instruction helpful.
-
robert from jacksonville, NC
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers
remove 2 screws pull out, and had a little trouble with the 2 power lines(breaker turned off), as they were around 60 years old, used a nut driver, and plyers to hold leads, and reversed to install. went well considering the age of the oven. tested, broiler works well,(let it heat up for appx 2-3 min to burn off dirt, etc)
Was this helpful?
Thank you for voting!
The oven just stopped heating. It is probably around 30 years old and has nothing digital to it which I like!
1 person
found this instruction helpful.
-
melinda from EL PASO, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set
I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then pu
... Read more
rchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!
Read less
Was this helpful?
Thank you for voting!
elememt not working
1 person
found this instruction helpful.
-
ROBERT from ORWELL, VT
- Really Easy
- 30 - 60 mins
-
Screw drivers
Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)
Was this helpful?
Thank you for voting!
bake element disintegrated
1 person
found this instruction helpful.
-
Susan from New Lebanon, NY
- Really Easy
- 15 - 30 mins
At 76 I no longer do my repairs so I asked my daughter's friend to do it for me.
Was this helpful?
Thank you for voting!
bake element burned out
1 person
found this instruction helpful.
-
Dave from Maryville, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
took cover off back of stove. Removed two screws and wires that were attached to the element. Removed old element and installed new element. An easy repair.
Was this helpful?
Thank you for voting!
The small element blew out consequently shorting out the infinite switch.
3 of 7 people
found this instruction helpful.
-
Susan from Bend, OR
- Really Easy
- 15 - 30 mins
-
Screw drivers
The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for m ... Read more y husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for m ... Read more y husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
Read less
Was this helpful?
Thank you for voting!
Bake element burned out in oven
1 person
found this instruction helpful.
-
AL from GENOA, NE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 ... Read more wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 ... Read more wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
Read less
Was this helpful?
Thank you for voting!