JMS0701 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burner wouldn't operate
3 of 5 people
found this instruction helpful.
-
Linda from Hindman, KY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel
Knott County Housing Authority Maintenance Personnel
Was this helpful?
Thank you for voting!
the items ordered replaced the worn out ones.
2 of 2 people
found this instruction helpful.
-
Carl from Morristown, N.J., NJ
- Really Easy
- Less than 15 mins
the replacement items fit really good. It was a matter of remove and replace,
Other Parts Used:
Was this helpful?
Thank you for voting!
Bake Element was bad and Drip bowls needed replaced
2 of 3 people
found this instruction helpful.
-
Randall from Lititz, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
First I turned the breaker off the Range. Second I removed the two screws that held the element inplace. Then I pulled element front until I could get to the two screw which connected the wires and removed then. Removed old Bake element. Installed new element by connecting the two wires and then pushed the element into place and secured i
... Read more
t by reinstalling the two screws. Turned the breaker back on and tested. This is a very easy item to replace and takes very little time.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Guest melted a nylon cutting board on the burner
2 of 3 people
found this instruction helpful.
-
Kay from Austin, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Ordered new burner and drip pan. New parts arrived within 3 days. Removed screw holding the hinge, removed clips from porcelain insulator, removed old burner, then installed new burner, reinstalled tilt lock hinge, replaced drip pan and ring and set burner in place. The whole installation took less than 10 minutes, and it works perfect
... Read more
ly.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
element burned out
2 of 3 people
found this instruction helpful.
-
Jeff from Westport, IN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
Was this helpful?
Thank you for voting!
Oven Heating element broken
2 of 3 people
found this instruction helpful.
-
James from Hanover, MA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New ele
... Read more
ment came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Read less
Was this helpful?
Thank you for voting!
Bake Element Burnt Out On Upper Oven
1 person
found this instruction helpful.
-
GREGORY from HOUSTON, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this helpful?
Thank you for voting!
Replacing the bake element
1 person
found this instruction helpful.
-
Ken from Lexington, KY
- Really Easy
- Less than 15 mins
-
Pliers
I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct par
... Read more
t shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.
Read less
Was this helpful?
Thank you for voting!
Lower baking element had burned out.
1 person
found this instruction helpful.
-
Rob from Las Cruces, NM
- Really Easy
- Less than 15 mins
-
Nutdriver
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewal
... Read more
l and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
The time it took was literally a few minutes. Works like a new oven!
Read less
Was this helpful?
Thank you for voting!
Baking element had burned out and actually cracked in half.
1 person
found this instruction helpful.
-
Marie from Roxboro, NC
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven ba
... Read more
ck. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Read less
Was this helpful?
Thank you for voting!
Customer service
2 of 4 people
found this instruction helpful.
-
Patricia from San Jose, CA
- Really Easy
- Less than 15 mins
Customer service is great. Fast shipping. Great communication. I have them bookmarked from a previous order. Same good service as the first time. Thank you.
Other Parts Used:
Was this helpful?
Thank you for voting!
Lower (bake) element burned out
1 person
found this instruction helpful.
-
gary from Broken Arrow, OK
- Really Easy
- Less than 15 mins
-
Nutdriver
Two 1/4" srews to remove the element from its mount, two 1/4" screws to remove wires and then the reverse to install new unit. Delivery was super fast and the price was half the price of the local dealers. I will certainly be a repeat customer.
Gary T.
Gary T.
Was this helpful?
Thank you for voting!
elemant had burnt into
1 person
found this instruction helpful.
-
Tracy from Paris, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned
... Read more
a spot in my Favorite list
Read less
Was this helpful?
Thank you for voting!
Heating Element Was No Longer Working.
1 person
found this instruction helpful.
-
Karen from Stuart, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Doug from Sewickley, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is stil
... Read more
l a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Read less
Was this helpful?
Thank you for voting!