JKC26404 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven would not get hot when on the BAKE setting
1 of 2 people
found this instruction helpful.
-
Kathy from Lincoln Park, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Four screws and two wires.
Was this helpful?
Thank you for voting!
old heating element burned out
1 of 2 people
found this instruction helpful.
-
Lee from Franklin, TN
- Easy
- Less than 15 mins
-
Pliers
unplugged oven. removed oven racks.Disconnected old unit. Installed new unit. Very very simple
Was this helpful?
Thank you for voting!
Bake unit had burned out
1 of 2 people
found this instruction helpful.
-
Margaret from Brookland, NY
- Really Easy
- Less than 15 mins
-
Socket set
With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.
Was this helpful?
Thank you for voting!
Oven element was shorted out
1 of 2 people
found this instruction helpful.
-
KEVIN from WAUSEON, OH
- Really Easy
- Less than 15 mins
-
Pliers
No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few second
... Read more
s element got hot, job done!
Read less
Was this helpful?
Thank you for voting!
Oven took long time to reach desired temp. Element sparkled and burned up.
1 of 2 people
found this instruction helpful.
-
Joe from Raleigh, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the ove ... Read more n on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the ove ... Read more n on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.
Read less
Was this helpful?
Thank you for voting!
bake element burned out
1 of 3 people
found this instruction helpful.
-
PIPER from DECATUR, GA
- Really Easy
- Less than 15 mins
-
Socket set
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to
... Read more
come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.
Read less
Was this helpful?
Thank you for voting!
Over took forever to come to temperature
0 of 1 people
found this instruction helpful.
-
Merle from Hainesport, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
My daughter and I turned off the breaker to the range and removed the old element and replaced it with the new one. My husband came home and took over after we had done almost everything ourselves!!
Was this helpful?
Thank you for voting!
Element Had Broken
0 of 1 people
found this instruction helpful.
-
James from Decatur, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
First we unplugged stove, if wired into circuit shut off in breaker box. Undo four screws on back cover and detach wires from element. Remove oven door by pulling open and sliding it up off hinges. Undo two screws holding element to back wall of oven. Slide in new element and replace screws in back wall. Replace door. Slide wi
... Read more
re leads on new element in back, at this point we plugged range in and tested element to see if heating. It worked so we replaced cover, slide range in and leveled it with wedges. Time for pizza.
Read less
Was this helpful?
Thank you for voting!
Oven Heating element burned out.
0 of 1 people
found this instruction helpful.
-
Rodney from Nokesville, VA
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair is simple. Unplug or turn off power to stove. Remove the 2 visible screw where the element connects to the back of the oven. Pull the element with back plate out. The back plate is part of the element. Remove 2 screws that connect wire. Mark which color connects to which lead. Re-assemble in reverse order. Takes about 1
... Read more
5 minutes,
Read less
Was this helpful?
Thank you for voting!
element burnt out
0 of 1 people
found this instruction helpful.
-
Cindy J from Reedsburg, WI
- Really Easy
- Less than 15 mins
-
Nutdriver
CAUTION: Make sure stove is unplugged as there is still current with it off! Removed 2 screws to pull old element out & 2 screws on electrical wires. Put new element in & screwed all screws, very easy repair. A big THANK-YOU to PartSelect for getting the part to us so fast!!
Was this helpful?
Thank you for voting!
Lower heating elemet burned out in oven
0 of 1 people
found this instruction helpful.
-
JOHN from MELBOURNE, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
It only took 15 minutes and a nut driver to replace.The part was $22,well worth keeping my oven going for a few more yaers
Was this helpful?
Thank you for voting!
Baking element burned out
0 of 1 people
found this instruction helpful.
-
Mark from Gordonsville, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Unscrewed the plate and unplugged the old element and plugged the new one in, screwed the plate back on. Done.
Was this helpful?
Thank you for voting!
Bake Element Not Working
0 of 1 people
found this instruction helpful.
-
Kimberly from Baytown, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Super simple installation. Once power was isolated from the oven, we removed the old bake element which had four nuts/screws. Then we installed the new element, turned the power back on and tested the oven. It worked perfectly! The whole process took maybe 5 minutes.
Was this helpful?
Thank you for voting!
Burned out oven element
0 of 1 people
found this instruction helpful.
-
Keith from Tacoma, WA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Simply removed the old part and istalled the new one with 2 nuts and 2 screws. It helps to know what the problem is. That comes with life experience.
Was this helpful?
Thank you for voting!
bake element in oven burned out
0 of 1 people
found this instruction helpful.
-
Charles from Bethlehem, PA
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench set
Removed old element from back of oven with closed wrench and removed wires from element with screwdriver. Took me longer to find screwdriver than to install part. Finding part and ordering it was a snap. Got part in day and half. Great service and price. This is the place for parts and instructions. Will definitly use it again. My wife th
... Read more
inks I'm a genious. Thanks PARTSELECT.
Read less
Was this helpful?
Thank you for voting!