EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JHP75G201 General Electric Range - Instructions

All Instructions for the JHP75G201
46 - 60 of 430

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
CERAMIC FUSE BLEW WHILE HEATING VEGETABLES
2 of 3 people found this instruction helpful.
  • Richard from SAN JOSE, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I found an exploded view diagram of of my microwave model which was very helpful. You need only remove outside metal skin by removing 4 screws on either side and 4 more on the back. Remove 4 plastic hole plugs from the top mounting inserts. Gently pull sides out and lift up and back to remove outer skin. The fuse is located on the back ri ght corner behind the control panel. You access from the side. The fuse is under the spreader bar. Lift fuse up gently to remove.

P.S. It was the MSP Capaciter and or the interlock switch, snap apart 21A (19) failure that actually caused the ceramic fuse to blow.
Was this helpful?
Thank you for voting!
Oven Heating element broken
2 of 3 people found this instruction helpful.
  • James from Hanover, MA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New ele ment came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.
Was this helpful?
Thank you for voting!
Broken element / light assembly
4 of 9 people found this instruction helpful.
  • Robert from Pompano Beach, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Piece of cake
Was this helpful?
Thank you for voting!
element burned out
2 of 3 people found this instruction helpful.
  • Jeff from Westport, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.
Was this helpful?
Thank you for voting!
Oven wouldn't hold temp - over/under
2 of 3 people found this instruction helpful.
  • Andor from Oxford, OH
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Unplugged the range, took old elements out, put new ones in. Couldn't have been easier and for the total cost of about $60; I have a working oven again. A LOT cheaper than a new $600 range!!
Was this helpful?
Thank you for voting!
BASE OF BULB BROKE OFF & WELDED TO SOCKET
1 person found this instruction helpful.
  • NEIL from ROCKY POINT, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.
Was this helpful?
Thank you for voting!
When moving the range, the 220 wire popped off the terminal and arced melting the plastic terminal
1 person found this instruction helpful.
  • Randall from ST PETERSBURG, FL
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 2 20 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.
Was this helpful?
Thank you for voting!
elememt not working
1 person found this instruction helpful.
  • ROBERT from ORWELL, VT
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)
Was this helpful?
Thank you for voting!
The bottom bake element burned out.
1 person found this instruction helpful.
  • Pauline from DECATUR, GA
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
1. Cut power off. 2. Remove old element, make sure you do not lose the screws, pull the connecting posts out and we used strings on posts so they could not get lost in the wall. 3. We then replaced the new element with little of no problems, it took approximately 30-45 minutes for the whole process.
Was this helpful?
Thank you for voting!
Replacing the bake element
1 person found this instruction helpful.
  • Ken from Lexington, KY
  • Really Easy
  • Less than 15 mins
  • Pliers
I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct par t shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.
Was this helpful?
Thank you for voting!
Bake Element Burnt Out On Upper Oven
1 person found this instruction helpful.
  • GREGORY from HOUSTON, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.
Was this helpful?
Thank you for voting!
Lower baking element had burned out.
1 person found this instruction helpful.
  • Rob from Las Cruces, NM
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Using a nut driver, I removed the two screws holding the baking element to the firewall of the oven. I then pulled the baking element out exposing the two wires connected to it. I then used the same nutdriver to remove the nuts and detached the old element. I then connected the new element to the wires, pushed the wires inside the firewal l and reattached the element to the firewall of the oven.
The time it took was literally a few minutes. Works like a new oven!
Was this helpful?
Thank you for voting!
Baking element had burned out and actually cracked in half.
1 person found this instruction helpful.
  • Marie from Roxboro, NC
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Socket set
It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven ba ck. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person found this instruction helpful.
  • Doug from Sewickley, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is stil l a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Was this helpful?
Thank you for voting!
Lower (bake) element burned out
1 person found this instruction helpful.
  • gary from Broken Arrow, OK
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Two 1/4" srews to remove the element from its mount, two 1/4" screws to remove wires and then the reverse to install new unit. Delivery was super fast and the price was half the price of the local dealers. I will certainly be a repeat customer.
Gary T.
Was this helpful?
Thank you for voting!
All Instructions for the JHP75G201
46 - 60 of 430