EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGS968SEKS General Electric Range - Instructions

All Instructions for the JGS968SEKS
106 - 120 of 145

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Our bottom drawer support broke and the bottom drawer was canted
  • Robert from Woodinville, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Simply removed drawer and lined up the newsupports. Made sure the guide pin was lined up and installed with single screw
Was this helpful?
Thank you for voting!
Broiler and Burners would light, oven would not light and you could smell gas, also before the oven stopped working the oven was taking awhile before it would light
  • Keith from San Diego, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
1.Removed the oven door. 2. Removed the oven floor panel ( slides right out ). 3. Removed cover plate and and removed one screw holding the igniter in place. 4 was able to pull the wire into the oven and unplug the igniter. Ordered a oven temp sensor but never needed it.
Was this helpful?
Thank you for voting!
Hard to move drawer in and out because the rear drawer supports broke off.
  • Steven from Lansdale, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Repair was very easy - less than a few minutes - just had to screw in 2 screws to the new drawer supports.
Was this helpful?
Thank you for voting!
Missing grate foot.
  • Barbara J from Sweetwater, TX
  • Really Easy
  • Less than 15 mins
  • Pliers
Ordered by phone parts & very pleased with all of transaction.
Was this helpful?
Thank you for voting!
Grate Foot Have 8 For My Stove And One Breaks Every Now And Then
  • Lee from Kenner, LA
  • Really Easy
  • Less than 15 mins
This was and always will be an easy fix, all I have to do is get my ice pick and pick the broken rubber part stuck in the hole if it does not break clean and fall out. Not much more I can say about this simple problem.
Was this helpful?
Thank you for voting!
Stove top worked, Broiler worked, but Oven would not heat
  • Vaughn from Visalia, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Odered igniter from part select, it arrived the next day. Removed oven door removed heat shield on bottom of oven and there it was. Removed the two screws pulled the wires till the connector came through, unpluged connector, plugged in new igniter, repaced everything and Bam, we were cooking. Did not even have to pull oven out from the wa ll. Super easy.
Was this helpful?
Thank you for voting!
faulty igniter
  • Gino from glen ellyn, IL
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
No response from GE website (very disappointing). google "repair GE gas range igniter" and very simple step-by-step instructions...apparently is very common with GE appliances...even mine that was less than 14 months old. Service tech would have charged $300. Did it myself for $80
Was this helpful?
Thank you for voting!
Ignitor burned out.
  • James from Salem, OR
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
Instead of trying to remove ignitor while mounted to burner, I removed burner/ignitor assembly by detaching it from the oven frame and pulling the ignitor/burner assembly out so connector cleared the access hole. Disconnected and removed whole assembly. Then had easy access to the mounting screws. Removed screws by first spraying threads with WD 40 and waiting. Screws were oxidized so they were damaged when backing them out, as were the threaded mounting holes in the burner ignitor bracket. The screws are not sheet metal as noted in other posts, but rather are 10-32 machine screws. I chased the ignitor mounting bracket threads, then remounted the ignitor with 10-32, 3/8's, cap head, stainless bolts with a stainless star washer (available at any ACE hardware or other similar store) -- that way you don't have to tighten up so tight (just snug them up) -- unless you expect an earthquake every other week. The stainless screws helps retard the corrosion brought on by high heat and any moisture that settles on the bolt threads as the system cools and with subsequent starts.
Was this helpful?
Thank you for voting!
had to replace burner
  • Janice F. from Dayton, NV
  • Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
I called Sears Repair to do the work. Glad I did because there's a lot more than just unscrewing screws...had to use the Dremel because the manufacture stripped one of the screws in assembly that was attached to the ignition part that connects to the burner...
Was this helpful?
Thank you for voting!
oven and broiler failed to light
  • DENNIS from Ronkonkoma, NY
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
pulled out appl,removed door,racks,lifted oven bottom to remove,removed both oven and broiler ignitors---went to back of appl to remove gas control valve and replaced--used old oven ignitor in broiler(took chance it would work-it did!)installed new ignitor in oven--tested perfectly--point of info if you have an oversize or dancing flame i n oven or broiler--remove flame tube and with 1/2 inch open wrench tighten orfice all the way until it stops--don't force or over tighten-- (the air shutter should open all the way)--flame should be about an 1 inch with white tips--adjust as needed-overall repair including adjustments took about an hour-hope this helps--and i'm not a professional repairman
Was this helpful?
Thank you for voting!
Oven would not heat
  • CELESTE from VAIL, CO
  • A Bit Difficult
  • 30 - 60 mins
  • Socket set
I removed the racks, burner cover, then unscrewed the cover for the starter. Had to get the correct ratchet to remove screws. The hardest part was removing two screws that held the igniter in place. Difficult location to get the tool in. They were also hard to put back. After that it was a matter of pulling the igniter out and discon necting it. You also have to remove the drawer under the oven so you can unplug the stove.
Was this helpful?
Thank you for voting!
burner flame out of control
  • tom from san pedro, CA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Wrench (Adjustable)
Replaced burner gaskets.
Was this helpful?
Thank you for voting!
The Oven would not light, but the Broiler would light
  • JOHN from FRESNO, AL
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Socket set
Read the experience of others on this website with the same problem. I knew exactly what to expect and it all went as the dozen previous oven repair experts had said. I can add my name to the list of experts. The two screws attaching the igniter to the bracket twisted off exactly like everyone else experienced. GE really should look a t developing a better attachment. My only problem was because my drill was larger than the bottom of the oven. I had to drill the holes on an angle. One of the holes was wallowed out more than the other. I had to use two different size screws and they were more difficult to screw in. Bottom line; I saved money, the oven works, my wife is happy, so I'm happy.
Was this helpful?
Thank you for voting!
Igniters on gas stove were randomly sparking.
  • William from New Concord, OH
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Backed off screws that held the burner base over the gas opening. Removed C ring and spring and slid out old igniter, cleaned base, inserted new igniter and replaced burner gasket, refastened base and the job was done. Repeated for other for burners. Easy.
Was this helpful?
Thank you for voting!
Self Clean would not start, Broiler would not turn on,
  • Carl F from Severna Park, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Socket set
Pull stove forward to access back. Remove center metal panel, 6 screws with 1/4" nut driver. Disconnect igniter connector. Measure resistance, it should be less than 1 ohm. Obtain new igniter. Test new igniter, 0.30 ohms. Remove oven door, see care and cleaning section of owner's manual. Remove burner cover, 2 screws with 1/4" nut driver. Remove two screws holding igniter. Aside: This is the second igniter to be replaced in this stove. The last one was exactly two years ago. Both times a screw snapped. With a small 5" vise grip the leading edge of the screw could be walked out. This time the two screws were replaced with 6-32 x 3/8" hex socket cap screws, split lock washer s under the screw head, and hex nuts holding the igniter in place. Note: All hardware was stainless steel. The burner cover was replaced. Oven door remounted. Igniter connected. Broiler turned on, it ignited. Center metal panel replaced. Stove moved into its nook.
Was this helpful?
Thank you for voting!
All Instructions for the JGS968SEKS
106 - 120 of 145