- Home
- JGS968SEKS
- Instructions
JGS968SEKS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Plastic slide for storage drawer broken.
-
James from Stuart, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took part out of package, looked at instructions and followed them. Required a screwdriver to screw part on to the drawer.
Was this helpful?
Thank you for voting!
Broken Door Switch
-
Peter from Green Valley, AZ
- Really Easy
- Less than 15 mins
I unplugged the defective plug and replaced it with the new one. Took 5 min total
Was this helpful?
Thank you for voting!
oven not warming, f2 indicating overheat
-
David from Lisle, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed 4 screws from back panel, disconnected small electricsl connector from sensor, removed one mounting screw from sensor inside oven,pulled wires through and removed old sensor. Fed wires for new sensor through and connected electrical connector, installed panel, installed mounting screw on sensor and checked oven, worked like a cham
... Read more
p. Took 5 minutes.
Read less
Was this helpful?
Thank you for voting!
the grate foots came off
-
Sandra from Watertown, MA
- Really Easy
- Less than 15 mins
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this helpful?
Thank you for voting!
Burners are supposed to burn with a blue flame. Two burners had yellow flames
-
Don from Port Orchard, WA
- Really Easy
- Less than 15 mins
New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.
Was this helpful?
Thank you for voting!
rear drawer supports broke
-
TERRY from RICHMOND, VA
- Really Easy
- 15 - 30 mins
-
Socket set
Directtions were by diagram only, no written instructions. Drawing was small and difficult to follow but the repair itself was easy.
Was this helpful?
Thank you for voting!
The oven temperature could not be controlled
-
Keith from Annapolis, MD
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later.
... Read more
Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Read less
Was this helpful?
Thank you for voting!
Oven slow to heat up
-
Joe from Harkers Is., NC
- Easy
- 15 - 30 mins
-
Nutdriver
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had
... Read more
the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Read less
Was this helpful?
Thank you for voting!
Oven would not light due to igniter.
-
Robert from Hillsboro, WV
- Really Easy
- 15 - 30 mins
-
Nutdriver
After reading reviews about corroded screws causing difficult removal I sprayed penetrating oil prior to installing replacement part. The oven doesn't need to be pulled out to fix. Just carefully pull wires through hole until the locking plug is visible & swap out. Very easy repair.
Was this helpful?
Thank you for voting!
f-2 or f-3
-
daniel from gap, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
remove two bolts in on sensor and slip thru back un plug and reverse to put in
Was this helpful?
Thank you for voting!
Ingiter would glow but gas would not come on
-
James from Coatesville, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I had read the customers reviews and expected that I'd most likely break the attaching screws. My trick was to not just unscrew then all the way out but to turn it a half a turn and then screw it back in. Then out again a little more then last time and back a little. Didn't break a thing. I did have to move the stove out to get to the plu
... Read more
g but that was just enough for me to get my arms in there.
Read less
Was this helpful?
Thank you for voting!
broken switch
-
Bob from Marcy, NY
- Easy
- 15 - 30 mins
-
Screw drivers
This was a wall mounted oven. Turned off breaker. Pulled panel off by removing 6 screws. Pulled connectors off old switch. Removed old switch. Just a friction fit. I used my jack knife to get it moving. Pushed in the new switch and connected wires. (just push on tabs) Put panel back together and turned on breaker. Done, easy.
Was this helpful?
Thank you for voting!
Convection fan came loose from shaft
-
Thomas from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Socket set
Convection fan came loose from the shaft with a lout rattle and grinding as the fan spun down. Had to remove four metal screws to remove the fan cover. Initially tried to just put the nut back on to hold the fan. However, I could not get the nut to start, so I assumed that threads were stripped on the nut or the shaft. Ordered the rep
... Read more
lacement nut, hoping that it was the nut that was the problem. However, I had the same problem with the new nut. I could see no damage on the shaft. It finally occurred to me that the nut and shaft had left-hand threads (counter-clockwise to tighten). At that point, it was extremely easy to put the nut back on and tighten it. I did not try using the old nut, since I had already received the new one, but I'm certain that if I had come to that realization earlier, I could have saved time and money. So, if you have the same problem, try putting the nut on "backwards."
Read less
Was this helpful?
Thank you for voting!
F2 reading
-
lynn from sunnyside, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Followed the instructions that were sent to me by E-Mail.
Was this helpful?
Thank you for voting!
Flashing F2 and erratic temperature readings.
-
Kenneth from Salem, OR
- Really Easy
- Less than 15 mins
-
Nutdriver
Unplugged from wall outlet, then opened oven front door. Reached in and removed two screws. Pulled oven sensor threw and detached electrical connector from old sensor. Plugged in new oven sensor and reversed removal procedure. No more Flashing F2 and oven temperature came to ready. Very easy.
Was this helpful?
Thank you for voting!