- Home
- JGS968BEKB
- Instructions
JGS968BEKB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 people
found this instruction helpful.
-
Chelagh from Fredericksburg, VA
- Really Easy
- Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
Oven will not heat
1 of 3 people
found this instruction helpful.
-
Joseph from Homosassa, FL
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
As many people have encountered, my oven would not heat but the igniter would be bright orange and glow! Over time, the igniter wears and degrades causing oxidation to the surface. This cause the igniter to fail and operate at a lower current level, below 2.8 amps! Normal igniters operator over 3.0 to 3.1 amps. When is happens, a low c
... Read more
urrent igniter does not have enough input to the control valve to tell the valve to open to allow gas to flow over the igniter to light the oven, thus heat the oven! This has got to be the NUMBER one reason for an oven not heating!
Read less
Was this helpful?
Thank you for voting!
Malfunctioning Regulator
1 of 4 people
found this instruction helpful.
-
Jesse from Lubbock, TX
- Really Easy
- 15 - 30 mins
-
Pliers, Wrench set
I replaced the regulator because it would close off when not in use. The regulator would not allow gas to flow for 15-45 seconds after 1 or more valves were opened. Everything functioned fine after the gas started flowing, but after a few minutes of having all burners off, you would have to wait for the regulator to open up when you nee
... Read more
ded to cook again. It was not the biggest problem in the world, but my wife complained like it was. The fix was easy and not to expensive, especially when you consider how much she was willing to pay the repair man. Hands on work was about 10 minutes. Gathering tools and teaching my son what I was doing took up the bulk of the time.
Read less
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 people
found this instruction helpful.
-
John from Tijeras, NM
- Really Easy
- Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
oven was not getting up to temp
0 of 1 people
found this instruction helpful.
-
walter from townshend, VT
- Really Easy
- Less than 15 mins
-
Nutdriver
Once I opened up the back of the range, the sensor wires where there and burnt just like your info said. One nut to take off in the oven and the sensor came right out and the new one went right in. The oven works great, cooked the turkey today. The worst part of the repare was the cleaning behind and under the range, it hasn't moved since
... Read more
it was put in 6 years ago. Very pleased with PS.
Read less
Was this helpful?
Thank you for voting!
F2 error when oven was heating up, along with a beeping noise and then it shut off
0 of 1 people
found this instruction helpful.
-
Lori from Paris, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this helpful?
Thank you for voting!
F2 error code
0 of 2 people
found this instruction helpful.
-
jud from gatesville, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's tha
... Read more
t easy. No more f2 been working like a champ!!!
Read less
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 people
found this instruction helpful.
-
Gene from Simi Valley, CA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In ... Read more sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Read less
Was this helpful?
Thank you for voting!
The spark module would constantly spark
-
Douglas from Knoxville, TN
- Really Easy
- Less than 15 mins
-
Screw drivers
I ordered the spark module and replaced it which was veru simple, plugged it in and it sparked only now and again. I finally said forget it and it has now stopped sparking but for how long I do not know.
Was this helpful?
Thank you for voting!
Burners are supposed to burn with a blue flame. Two burners had yellow flames
-
Don from Port Orchard, WA
- Really Easy
- Less than 15 mins
New burner Heads repaired the two yellow burning units. I believe heat caused the old heads to become. warped over time.
Was this helpful?
Thank you for voting!
Stove drawer rear guides broken
-
Robert from Shakopee, MN
- Really Easy
- Less than 15 mins
-
Nutdriver
Installed new guides with a nut driver without any problems.
Was this helpful?
Thank you for voting!
gasket on door was brittle
-
Barbara from Bethesda, MD
- Really Easy
- Less than 15 mins
I feel like Macho Mom. I called in the repair guy since I was afraid of dealing with the gas. HE repaired one item but could tell I was comfortable fixing things and pointed out that the gasket was brittle and would cause major problems if not replaced. Took longer to order the part than do the repair, don't know what I was afraid of!
Was this helpful?
Thank you for voting!
warped burner
-
judith from boardman, OH
- Easy
- Less than 15 mins
reinstalled new one. just a little better than than the warped one.
Was this helpful?
Thank you for voting!
Range lower drawer would not stay on track.
-
Richard from Newark, DE
- Really Easy
- Less than 15 mins
-
Nutdriver
Easy to install replacement parts using the screws provided.
Was this helpful?
Thank you for voting!
Broken drawer support
-
Mario from Deer Park, WA
- Really Easy
- Less than 15 mins
-
Nutdriver
Followed the example picture on the part bag. Anyone could do this, incredibly easy. Took about 4 minutes to install both sides.
Was this helpful?
Thank you for voting!