EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGS968BEKB General Electric Range - Instructions

All Instructions for the JGS968BEKB
61 - 75 of 144

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The storage drawer came without supports.
2 of 4 people found this instruction helpful.
  • Dock from Aurora, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person found this instruction helpful.
  • Ron from SAN TAN VLY, AZ
  • Very Easy
  • Less than 15 mins
  • Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
GAS OVEN WOULD NOT HEAT - NO FLAME AT BURNER
1 person found this instruction helpful.
  • BOB from BURBANK, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Could not have been easier. All screws are 1/4 inch. Oven door can be removed to make it easier to get to screws in back of oven,but igniter can be installed with door in place. Remove bottom panel then remove four screws on flame spreader. Remove trwo screws that hold igniter in place. Replace with new igniter, it may be necessary to r emove the clip on new igniter and splice the two leads. Now your cooking with gas.
Was this helpful?
Thank you for voting!
Oven lamp globe shattered . Needed a replacement
1 person found this instruction helpful.
  • Joan from SOUTHINGTON, CT
  • Very Easy
  • 15 - 30 mins
The oven lamp shattered while cleaning. Easy to replace by hand.
Was this helpful?
Thank you for voting!
Followed a GE Video on installation
1 person found this instruction helpful.
  • Sarah from MONTGOMERY, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed GE repair video
Was this helpful?
Thank you for voting!
Rubber grate foot failed
1 person found this instruction helpful.
  • Gary from HENDERSONVLLE, NC
  • Very Easy
  • Less than 15 mins
Cut off approx. 1/8" in length for correct fit.
Was this helpful?
Thank you for voting!
door gasket was soiled
1 person found this instruction helpful.
  • Joseph from Murrells Inlet, SC
  • Really Easy
  • Less than 15 mins
took out old gasket and inserted new
Was this helpful?
Thank you for voting!
Sparking at 2 different burners all by themselves
3 of 7 people found this instruction helpful.
  • paul from las vegas, NV
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Replaced Spark Module and adjusted igniters
Was this helpful?
Thank you for voting!
Replace the lower oven gas igniter
1 person found this instruction helpful.
  • Edward from New York, NY
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Flip toggles to release the oven door. Pull up on oven door to remove. Put door aside. Lift enamel bottom. Slide strait out. Remove aluminum shielding from around the igniter. Loosen igniter, unplug the igniter. Remove burner cowling. Plug in new igniter. Attach cowling to new igniter. Screw it all back in place. Stuff wiring con nected back through the protective hole. Depress close door button and test. It takes about 10-15 seconds to ignite. Reinstall aluminum protector. Re install bottom enamel piece. Carfully slide oven door back on pegs and flip toggles to lock. Have a big glass of water and yell, Honey I fixed the oven!!
Was this helpful?
Thank you for voting!
Lower oven would not light consistently
1 person found this instruction helpful.
  • Brad from PARIS, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Wrench (Adjustable)
I did find instruction in the Q&A on how to to change the part was for an older oven.

Here are the instructions that matched my oven model "JGSP42SET1SS"

https://www.youtube.com/watch?v=aHg-O1-NnXM

I also had issues where the connector for the new part would not come through the hole in the back of the o ven. I used a shoestring around the connector so I would have a good grip on it when I disconnected the old igniter.This allowed me to have a good grip to reconnect to the new igniter.

While you have this apart I would also recommend that you remove the burner and blow out any material that may have accumulated over the years,
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people found this instruction helpful.
  • NICK from Vernon, CA
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
The Grate foot is to big for the hole.
1 of 2 people found this instruction helpful.
  • Harold from Broadalbin, NY
  • A Bit Difficult
  • 15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
bake cycle would not work
1 of 2 people found this instruction helpful.
  • Jenn from FORT WORTH, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
open the oven door (remove) ,disassemble the igniter ,replace the igniter .
Was this helpful?
Thank you for voting!
Light bulb went out,could not find replacement part.
1 of 2 people found this instruction helpful.
  • Gregory from Pearl River, LA
  • Really Easy
  • Less than 15 mins
Turn the glass enclosure counterclockwise to expose bulb.Turn the power off at circuit breaker panel.Handle the bulb carefully with paper towel covering the bulb.Push the bulb in socket.replace glass enclosure,turn power back on.
Was this helpful?
Thank you for voting!
very easy
1 of 2 people found this instruction helpful.
  • ROBERT from CYPRESS, TX
  • Really Easy
  • Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
All Instructions for the JGS968BEKB
61 - 75 of 144