EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JGP975BEKB General Electric Range - Instructions

All Instructions for the JGP975BEKB
16 - 30 of 34

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The Grate foot is to big for the hole.
1 of 2 people found this instruction helpful.
  • Harold from Broadalbin, NY
  • A Bit Difficult
  • 15 - 30 mins
I had to drill the hole to a larger size to enable the foot to fit.
Was this helpful?
Thank you for voting!
very easy
1 of 2 people found this instruction helpful.
  • ROBERT from CYPRESS, TX
  • Really Easy
  • Less than 15 mins
there were no grate pads so it was easy to add them.
Was this helpful?
Thank you for voting!
Hot burner light lens broke off.
1 of 2 people found this instruction helpful.
  • Charles from NEKOOSA, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
Pull range away from back wall. Remove panel behind control knobs by removing the screws that hold it on. Find hot burner light that holds lens. Remove broken part of lens. Insert new lens into hole on front of control panel and into hot burner light receptacle. Replace back panel. Slide range back into place.
Was this helpful?
Thank you for voting!
The electrode had broke
1 of 2 people found this instruction helpful.
  • O.Robert from Montrose, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
I unscrewed the base where the electrode was attached to detached the electrode detached the wire to the electrode inserted new electrode with holding spring and clamp attached wire to electrode.
I then put the base back on top and screwed in the two screws assembled the remaining parts and turned on the stove unit and it worked I am very happy.
Was this helpful?
Thank you for voting!
worn and pitted burner caps
2 of 5 people found this instruction helpful.
  • Ann from Ashland, MA
  • Really Easy
  • Less than 15 mins
Removed the old caps and replaced with new burner caps. The stove top looks brand new. Thank you.
Was this helpful?
Thank you for voting!
The Grate Foot was deteriorated on several sections for my cook top. The hardest part was finding the right part.
1 of 3 people found this instruction helpful.
  • Chelagh from Fredericksburg, VA
  • Really Easy
  • Less than 15 mins
Nothing technical.
Was this helpful?
Thank you for voting!
Could Not Remove Orifice
0 of 1 people found this instruction helpful.
  • Jim from Macedon, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Wrench set
I had to convert unit to propane and it was new out of the box. Could not remove one orifice because it had been installed too tight so I called ge for service as a warantee call we were on the phone with ge customer service for well over an hour and were transferred about 5 times all resulting in dropped calls. So, I contacted parts se lect and of course, paid for the part myself just get it done. It was easier that trying to work with ge. Received the part and and completed the conversion without difficulty. Along with the range top, we completely outfitted our remodeled kitchen with profile appliances including 2 ovens, dishwasher, refrigerator and a trash compactor. However, parts select was great.
Was this helpful?
Thank you for voting!
Grate foot bdroke off allowing grate to scratch cooktop
0 of 1 people found this instruction helpful.
  • John from Tijeras, NM
  • Really Easy
  • Less than 15 mins
Used scribe to remove grate foot plug still in grate inserted new foot.
Was this helpful?
Thank you for voting!
To Replace Gas And Burner Parts In Section 4
0 of 1 people found this instruction helpful.
  • John from Long Beach, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers, Wrench set
Start by removing all screws 3 for each burner total of 15 t-15 bit is required then proceed to remove spark igniters 5 total slight pull next step would be to slide a screwdriver under top left and right side to remove top shelf. There you will have access to the parts you need to replace. When done just reverse installation instruction s to complete
Was this helpful?
Thank you for voting!
Leaking from front door
1 of 9 people found this instruction helpful.
  • Gene from Simi Valley, CA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First remove the screws around the inside perimeter of the door. These require a special hex driver. Take off the inside plastic liner of door.
Peal off the old Insulation Foam Strip and replace it with the new strip in the same location. Make sure the wires are off to the right side. Replace the door plastic liner. Done. The In sulation Foam Strip really acts more like a loose gasket to keep spashing from creeping under the door and drippin out on the floor.
Was this helpful?
Thank you for voting!
Stain/polyurethane dried on burner head & cap
  • Stephen from Ogdensburg, NY
  • Really Easy
  • Less than 15 mins
Lifted both pieces off and placed the new ones on,turned on the burner and it worked as it should.
Was this helpful?
Thank you for voting!
Orange light "Hot Stovetop" lense broke off.
  • John from Woodbridge, VA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
Parts arrived in record time and the right parts. The detailed diagram was so helpful in finding exactly the part I needed to order. Was so easy my girlfriend with no mechanical or electrical experience completely helped me through the entire project. She secured the electrical breaker to the range, and I had the top back to the oven r emoved. I showed her how the little white box simply slides off the lens cover, then replaced the new one in the holes and slide it back on. Secured the back and she turned on the breaker back on...and all lights work. Thanks for making this project easy, simple and quick.
Was this helpful?
Thank you for voting!
Burner would not ignite.
  • John from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
Could not have been simpler. Burner head dropped into place and was held in place by gravity. Not possible for part to go in incorrectly.
Was this helpful?
Thank you for voting!
the grate foots came off
  • Sandra from Watertown, MA
  • Really Easy
  • Less than 15 mins
put it in but it keeps falling out. they're made narrower than my oven grate.
Was this helpful?
Thank you for voting!
Replace medium burner for gas cooktop
  • Charles from Houston, TX
  • Really Easy
  • Less than 15 mins
Very easy to remove grates, burner cover and remove old burner head. Very simple process, but surprised that there was no efficient way to clean carbon deposits from my old burner. Burner video instructions on line insured I installed the new burner head correctly (actually, pretty hard to get wrong), and burner worked correctly immediate ly. Will likely replace other burners in time as the new one is so "silvery" colored compared to my other burners.
Was this helpful?
Thank you for voting!
All Instructions for the JGP975BEKB
16 - 30 of 34