JDS28CKC General Electric Range - Instructions

Took off the ring burners and the old drip pans . installed the new drip pans and the old burners took less than 3 minutes...so easy

I am a 62 y/o single female and was able to make this exchange of parts with ease. The toughest was getting the old terminal's wire clips free from years of gunk! I was pleased with the ease of installation and that it really worked afterwards. By the way, thank you Parts Select for getting this part to me very quickly. If a novice c ... Read more an diagnose, find the correct part and install it with success then anyone could do the same.

I knew I had a bad control board. Using the repair videos, replacing this part was very easy to do. While I was at it, I replaced my oven temperature sensor. as well, and even though it wasn't bad, I replaced my oven heating element so that I could get some more mileage out of my 14-year-old range. The issue: after completing my repair ac ... Read more tions, my oven element still would not heat. I double-checked my connections and I discovered I hadn't ensured one of the wires on the control board was properly seated. This was one of the wires that go to the heating element. After ensuring proper connection, everything worked perfectly!

make sure to throw breaker and power is off of range, the elements still have power on them when range is off. Took door off, pulled racks out, pulled the two screws holding the element in place. Pull elements straight out and unplug the wires connecting to thr element and reverse the prosses.

Cut 4 inch’s off the new terminal block wires then using my wire strippers stripped 1/2 inch off the ends , the old terminal block wires I stripped 1/2 inch at the ends using a wire nuts on both wires and electrical tape connected the terminal block to the stove plugged the new burner in and the burner worked 100%.

Took back off and replaced.

Sensor is in rear and on top ov oven. What could be a 10" job took 45". My problem was the oven door was diffinately in the way. Also I wear bifocals which makes me tilt head to see nuts. I felt like a contortionist. HINT: remove door and give yourself some room to work.

Turned off breaker to oven at breaker box. Removed the 2 screws. Gently pulled the heating element out enough to remove the 2 wires. Connected the 2 wires to the new element. Pushed connecdted ends back into hole and replaced and tightened 2 screws. Turned breaker back on, tested oven, and it worked.

unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .

Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certai ... Read more n areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.

Took back cover panel off (upper) and removed the 4 1/4 inch nut screws. Used nut driver and removed the 4 screws holding control panel in place. Put new panel in place and unhooked electrical connections and installed on new panel. Plugged stove back in and checked operation. All OK, so then put back cover on and everybody is happy.

It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.

Replaced element control switches

Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.

I just follow Steve's Installation Vidio. My range works.
Thanks Steve