EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JDP39DN1WW General Electric Range - Instructions

All Instructions for the JDP39DN1WW
121 - 135 of 276

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake button stopped registering
1 person found this instruction helpful.
  • Ryan from COHOES, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.
Was this helpful?
Thank you for voting!
ONE OF SURFACE BURNER NOT WORKING
1 person found this instruction helpful.
  • QUANG from LANCASTER, PA
  • Really Easy
  • 30 - 60 mins
  • Nutdriver
I UNPLUGGED THE WIRE, ASSEMBLE THE BURNER ELEMENT KITS
LIFTED UP THE SURFACE BURNER PANEL,
OPENED THE BACK RANGE COVER,
UNSCREW THE NUT HOLDING THE BURNER CONNECTOR, DISCONNECT THE REPLACEMENT WIRES ON THE BACK PANEL
TRACE THE NEW WIRES CLIPS TO THE BACK PANEL & TIGHTEN THEM WITH EXISTING NUTS
SCREW THE OTHER EN DS BACK WITH NUT HOLDING THE BURNER CONNECTOR
Was this helpful?
Thank you for voting!
Two blocks kept shorting out.
1 person found this instruction helpful.
  • Evelyn from FRANKLIN, NH
  • Easy
  • 1- 2 hours
  • Socket set
After watching the video and ordering the parts and searching for the right size socket (which took most of the time) and finding medical tape as I had no electrical tape I took of the back unhooked the terminals and following the wires to determine which ones needed to be replaced I followed the video instructions on reverse as my son h ad spliced new terminal blocks into the old wires I taped each new wire to the one it was replacing and pulled it through the back of the stove and into the front attached the new wires to the new block and pushed the clips on the other end of the wires to the knob boxes. I rolled up the excess wire and taped it securely with medical tape so it wouldn't unravel and be in the way when I reattached the back shield on the stove. After I repeated the process for the second terminal (I had two that kept shorting out) I reassembled the stove plugged it back into the wall and used both burners that night to cook dinner! I have had no problems with those burners since then. Really if you watch the video first and follow the instructions you should have no problems. It is really quite simple if someone hasn't tried to repair the problems without replacing the wires. Splicing new blocks into old wires just doesn't work. If I have this problem again, which I hope I don't, I will be confident in my ability to fix the problem myself. Thank you parts select for repair video and the parts.
Was this helpful?
Thank you for voting!
Needed New Burner Bowls
2 of 4 people found this instruction helpful.
  • Carolyn from Garden City, ID
  • Really Easy
  • Less than 15 mins
Removed the old burner bowls, replacing them with the new ones.
Was this helpful?
Thank you for voting!
Lower bake element was not working.
2 of 4 people found this instruction helpful.
  • James from Miami, FL
  • Really Easy
  • Less than 15 mins
  • Socket set
Simple job. Disconnected the power to the oven, removed the two screws holding the old lower element, pulled it out and disconnected the two electrical wires. Installed the new one by simply reversing the removal process. Very impressed with PartSelect on price and delivery. My local repair company wanted to charge me twice the price and a part delivery time three times longer. Will definitely use PS in future
Was this helpful?
Thank you for voting!
Could not adjust heat on burner.
2 of 4 people found this instruction helpful.
  • Roy from Au Gres, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Followed directions given by previous customers problems which we found on the internet.
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people found this instruction helpful.
  • Melvin from Portland, TN
  • Easy
  • Less than 15 mins
  • Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
shortage in wiring cause the housing to burn out
1 person found this instruction helpful.
  • fred from PALM COAST, FL
  • Really Easy
  • Less than 15 mins
Replaced new light housing.
Thanks to you guys for the prompt response
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person found this instruction helpful.
  • Melvin from WEBSTER, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
Followed a GE Video on installation
1 person found this instruction helpful.
  • Sarah from MONTGOMERY, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed GE repair video
Was this helpful?
Thank you for voting!
The heating element failed for the oven. Broiler element continued to function.
1 person found this instruction helpful.
  • Steve from ANAHEIM, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
This is a pretty easy job. Took 20 min. because I was especially careful. Once the new element arrived, I simple shot off the power (DO THAT, BE SURE TO DO THAT ). Two 5/16 screws hold the element in place at the rear of the oven. Once removed the element can move forward. A surprise was that wires attached to the element come with it. There are simple push on connections on the element. There were a little difficult to remove (heat I am sure ), but a couple of needle nose plyers and the two wires removed with ease. Plug in the new element connectors and push the wires and the connection back into place. Once in place, reinstall the screws and test.
Was this helpful?
Thank you for voting!
oven racks old and ugly
1 person found this instruction helpful.
  • Claudene from ORCUTT, CA
  • Very Easy
  • Less than 15 mins
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this helpful?
Thank you for voting!
burner was not heating
1 person found this instruction helpful.
  • lucille from HAPPY CAMP, CA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
unplug it and plug the new one in
Was this helpful?
Thank you for voting!
Oven quit heating
1 person found this instruction helpful.
  • LARRY from MOSELLE, MS
  • Really Easy
  • 15 - 30 mins
  • Socket set
Disconnected power, removed two screws from bracket. Unplugged old element, installed new element and replaced screws in bracket. Restored power and back in business!
Was this helpful?
Thank you for voting!
control switch had stopped working, burner wouldn't work properly
1 person found this instruction helpful.
  • Ruth from JACKSON, MO
  • Really Easy
  • Less than 15 mins
  • Screw drivers
took out a couple of screws and replaced with new switch, plugged in switch wires. very easy
Was this helpful?
Thank you for voting!
All Instructions for the JDP39DN1WW
121 - 135 of 276