EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JDP39DN1WW General Electric Range - Instructions

All Instructions for the JDP39DN1WW
91 - 105 of 276

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Was burned out
2 of 2 people found this instruction helpful.
  • BRINDIA from DOVER, TN
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Took back off and replaced.
Was this helpful?
Thank you for voting!
Oven would shut down while baking. Stove top would work.
2 of 2 people found this instruction helpful.
  • Tom from ELIZABETHTON, TN
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Replaced Electronic Control Board. Very easy to do with a nut driver and a screw driver to remove the old one. You may need a pair of needle nose pliers to remove Connector TB100 and TB101. Just squeeze the bottom of tabs to release connector. I also found that in the process of removing the Control Board label that it may rip in certai n areas even while using a razor blade, so be prepared to purchase a craft paint brush and craft white paint to touch up the back of the label. It took 2 coats but looks like new..

The replacement Control Board works as advertised and I now have my oven working again. Save yourself the cost of a Service Company coming into your home just be prepared to do a bit of painting on the old label because it is really glued down and the new control board does not come with a new label.
Was this helpful?
Thank you for voting!
lights blown out
6 of 14 people found this instruction helpful.
  • Gerald from WINTERVILLE, GA
  • Very Easy
  • Less than 15 mins
replaced lights in refrigirator and freezer
Was this helpful?
Thank you for voting!
Top left electric burner on the stove top did not heat up
2 of 2 people found this instruction helpful.
  • Jeff from SAN RAFAEL, CA
  • Really Easy
  • Less than 15 mins
Simple to repair. Take off the cowling around the burner element on the stove top and pull out the old element. Slide in the new heating element with the cowling paying attention to the three spoke support areas on the stove burner frame. Very simple. A 5 minute repair. No tools required.
Was this helpful?
Thank you for voting!
Replaced Oven Thermostat Sensor in oven
2 of 2 people found this instruction helpful.
  • C Thomas from SAN MARCOS, CA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
1) Shut off power to oven
2) Removed oven door using snap down hinges on door
3) Removed 4-phillips head screws holding the oven frame to cabinets
4) Pulled oven out of cabinet and set it on stool in front of opening
5) Remove 2-hex screws holding metal shield covering the electrical wiring on back of oven
6) Unpl ugged bad thermostat connector
7) Removed the single hex screw holding thermostat inside the oven
8) Pulled the thermostat and lead wire from oven
9) Fed the new thermostat wire into inside back of oven
10) Reverse steps 1-7
Was this helpful?
Thank you for voting!
oven racks very old and writing on knobs worn ff
2 of 2 people found this instruction helpful.
  • Patricia from SAN JOSE, CA
  • Very Easy
  • Less than 15 mins
Very was ti replace racks and knobs. Very fast mail service
Was this helpful?
Thank you for voting!
Oven temp wouldn't regulate.
2 of 2 people found this instruction helpful.
  • Ronald from Crumpler, NC
  • Very Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Followed the directions!
Was this helpful?
Thank you for voting!
Just didn't work no pwr to it
2 of 2 people found this instruction helpful.
  • Jerry from HOPEWELL, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Killed braker first, removed four screws from back, then unplugged all the wiring, then removed four screw that hold the unit on stove, pealed off the face decal, put that on the new on and just reversed the take off press.
Was this helpful?
Thank you for voting!
front lift burner not working and surface light on with everything off
2 of 2 people found this instruction helpful.
  • kevin from GAYLORD, MI
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
unplugged the range removed 4 screws from back top cover then took the knob off controller removed 2 screws from behind the knob removed 1 wirer at a time and placed it on the new controller in same order the wires came off put everything back to gather did not fix the problem .
Was this helpful?
Thank you for voting!
Defective switch
2 of 2 people found this instruction helpful.
  • Mary from EDENTON, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Replaced element control switches
Was this helpful?
Thank you for voting!
Surface burner stopped working & light indicator remained on
2 of 2 people found this instruction helpful.
  • Cynthia from BALDWINSVILLE, NY
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
It took my son very little time to install control switch. Using a screw driver he removed the back panel directly behind burner units & replaced the control switch. Very easy.
Was this helpful?
Thank you for voting!
burner was damaged so it didn't work
2 of 2 people found this instruction helpful.
  • Joan from ORLANDO, FL
  • Really Easy
  • Less than 15 mins
Easy repair, just had to take the damaged burner out and slide the new burner in....
Was this helpful?
Thank you for voting!
broken light cover
2 of 2 people found this instruction helpful.
  • Francis from LAKE ELSINORE, CA
  • Very Easy
  • Less than 15 mins
twisted it in place
Was this helpful?
Thank you for voting!
I had to replace the surface heating element on my Selectra stove top.
2 of 2 people found this instruction helpful.
  • Elaine from SAINT JAMES, NY
  • Very Easy
  • Less than 15 mins
I just inserted the replacement where the old one had been connected. It took less than 5 minutes. It was so simple & easy that 'repair' is too generous a word -- & I am NOT handy, in any sense of the word. It took me longer to figure out where to find the model number!
Was this helpful?
Thank you for voting!
Needed new drip pans
2 of 2 people found this instruction helpful.
  • Patricia from GORDONVILLE, TX
  • Really Easy
  • Less than 15 mins
Replaced drip pans
Was this helpful?
Thank you for voting!
All Instructions for the JDP39DN1WW
91 - 105 of 276