EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCSP31WV2WW General Electric Range - Instructions

All Instructions for the JCSP31WV2WW
121 - 135 of 340

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
heating element burnt through
0 of 1 people found this instruction helpful.
  • Michele from Columbia, IL
  • Really Easy
  • Less than 15 mins
Very easy repair. Part came wrong the first time (my fault for ordering the wrong one). Called and ordered the correct one after a closer match to the original part. Delivered much quicker than promised (one day) and installation very easy. Will use this site for all future repairs.
Was this helpful?
Thank you for voting!
20 year old oven bake element became brittle and pieces broke off, overheated and partially melted, one side touching bottom of oven, caused very slow heatup.
0 of 1 people found this instruction helpful.
  • Leonard from Framingham, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
Removed nuts holding element to rear of oven using nut driver, pulled wires out 3 inches and disconnected using needle nose pliers, installed new element. Job took 10 minutes - very easy job and works fine.
Was this helpful?
Thank you for voting!
Element burned out
0 of 1 people found this instruction helpful.
  • Bryan from Overland Park, KS
  • Really Easy
  • Less than 15 mins
  • Screw drivers
AMAZING SHIPPING.Ordered on Friday,received saturday WITHOUT NEXT DAY COST.Amazing,worked perfect.
Was this helpful?
Thank you for voting!
Burner not working.
0 of 1 people found this instruction helpful.
  • Scott from Dallas, GA
  • Really Easy
  • Less than 15 mins
I pulled the old burner out and slid the new one in it's place. Turned on the eye to make sure it worked. Felt heat in a few seconds and turned off.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
0 of 1 people found this instruction helpful.
  • Craig from Catasauqua, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Turned power off. Removed two screws holding the element. Pulled element out 3 inches, disconnected the two wires, pulled out old element, connected wires of new element, replaced screws. Turned power back on. Eureka!! the oven heats again. :-)
Was this helpful?
Thank you for voting!
the old oven element burned in two.
0 of 1 people found this instruction helpful.
  • Kenneth from Newport, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver
After removing the screws holding the element in I disconnected the wires and attached alligator clips to the wires to keep them from pulling back inside the holes. I would have had to pull the stove out and removed some covers if they disappeared through the holes. After getting the part number off of the old element, I ordered a new e lement from Partselect.com and received the new one in less the a week. Reinstalling the new element took about 5 minutes.
Was this helpful?
Thank you for voting!
Bottom element cracked/split - open circuit
0 of 1 people found this instruction helpful.
  • Al from Charlotte, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed oven shelves (30 seconds). Removed 2 screws holding broken element to oven (2 minutes). Pulled broken element assembly out & removed 2 wires attached to element (1 minute). Connected wires to new element (just push them into place) and mounted new element with the 2 screws (1 1/2 minutes). Turned on oven element to test & sinc e I was so tired from all of this 5-minute activity, I rested.

Al S.
Was this helpful?
Thank you for voting!
Element broke
0 of 1 people found this instruction helpful.
  • Kim from Vancouver, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers
First I switched the fuse to the oven had no power and then I removed the old element and wiped down the inside with a damp towel.
I then attached the new element and then used the screws to attach the element firmly into place.
I then restored power by switching the fuse back and then burned the element to remove and chemicals and then done
Was this helpful?
Thank you for voting!
Oven would not heat up
0 of 1 people found this instruction helpful.
  • John from Wetumpka, AL
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Took out the hexagon screws, used pliers to pull the connecting ends apart, slid in the new element in to the connecting slots, reattached to screws, turned on the oven to see if it would heat up and it did. It was really easy. I had waited for a week to get the part from my local Sears parts house. You sent it out and I had it in 3 da ys. They still don't have the part. Thanks so much.
Was this helpful?
Thank you for voting!
I ruined old unit
0 of 1 people found this instruction helpful.
  • Arthur E. from St. Louis, MO
  • Really Easy
  • Less than 15 mins
Removed old, and replaced with new, heating element! Maybe 10 seconds.
Was this helpful?
Thank you for voting!
botton bake element burned out
0 of 1 people found this instruction helpful.
  • John from Plano, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed to screws holding the bake element in place. pulled out element to get to the 2 electrical connectors. removed connectors from old unit. connected new unit and secured with the screwes. very simple.
Was this helpful?
Thank you for voting!
For some time our oven had been working eratically, temperature spikes and drops during baking process. I thought the thermostat was the problem. The last time baking, element sparked and overheated in one spot so we removed the element. It was warped and cracked. We replaced it with the new ele
0 of 1 people found this instruction helpful.
  • Marshall from Prosser, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I removed the two screws with a nut driver, pulled the element out far enough to expose the connection point and disconnected the electrical clips. Upon receipt of the new element I did those things in reverse order and it worked great.
Was this helpful?
Thank you for voting!
10-yr old Baking Element gave out
0 of 1 people found this instruction helpful.
  • Timothy from Boise, ID
  • Really Easy
  • Less than 15 mins
  • Nutdriver
This repair was idiot-proof. Removed 2 screws, unplugged the old part, plugged in the new one, and replaced the 2 screws.
Literally a 2 minute repair!!
Was this helpful?
Thank you for voting!
Element no longer heated
0 of 1 people found this instruction helpful.
  • Karen from Gladstone, OR
  • Really Easy
  • Less than 15 mins
  • Pliers, Socket set
Piece of cake. 2 screws and a flashlight. I needed needle nose pliers to insert the "plugs" into the "sockets."
Was this helpful?
Thank you for voting!
Bake Element Defective
0 of 1 people found this instruction helpful.
  • Glenn from Newnan, GA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Cut power to oven from breaker box. Remove two retaining screws using a nutdriver at rear of oven. Slowly pull Bake Element from rear of range exposing connector clips. Disconnect at clips from oven wiring. Connect new Baking Element to wiring connectors. Push new baking element into rear of oven. Reconnect baking element using origin al screws with nutdriver at rear of oven. Turn on power to oven from breaker box. Job complete in 10-15 mins.
Was this helpful?
Thank you for voting!
All Instructions for the JCSP31WV2WW
121 - 135 of 340