EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCSP31WV2WW General Electric Range - Instructions

All Instructions for the JCSP31WV2WW
76 - 90 of 340

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
My heatng element blew up
2 of 4 people found this instruction helpful.
  • Ruth from Charlotte, NC
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Wrench (Adjustable)
I followed the way all the others on this website did the repair. It was so easy. I turned the power off to the oven, then disconnected it from the back oven wall, pulled it out a bit, disconnected the wires, and put it back in.

Then we put the power back on and stood back and turned on the stove and IT WORKED!!! Yeah, and for so little money... I tell you I shopped other websites and this one was priced GREAT, and just reading the stories how others had done this repair gave me the confidence to do it too. Now, I think I have a burner that I will replace and who knows what else I can find to do.

THANKS SO MUCH!!!
Was this helpful?
Thank you for voting!
The bottom bake element was burned out.
1 person found this instruction helpful.
  • Richard from State College, PA
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
1. Turned off electrical breaker for range.
2. Removed the two hex head screws that hold element in place.
3. Pulled element out and unplugged the two electrical connectors.
4. Attached connectors to new element and attemped to push element back into the opening. It would not go in all the way.
5. Apparently some of t he insulation had fallen down and was blocking the area where the element slides in.
6. I used a long thin screwdriver inserted into the two holes to push the insulation aside.
7. The element was then able to go in all the way.
8. Replaced two hex head screws.
9. Turned on range breaker.
10. Turned on oven. Works fine.
Was this helpful?
Thank you for voting!
bake element broke
1 person found this instruction helpful.
  • edward from west sayville, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
first i removed the two screws that hold the element in place. then pulled the element out about 3 inches and disconnected the two wires .then i connected the two wires and pushed thebake element back and replaced the two screws.then i put the circuit braker back on and tested the stove and it worked great. very easy to do.
Was this helpful?
Thank you for voting!
Bake element sparked due to damage
1 person found this instruction helpful.
  • Robert from Bethlehem, NH
  • Really Easy
  • Less than 15 mins
  • Socket set
Shut of circuit breaker. Removed two screws with socket set . pulled element out about three inches, disconnected and held wires in place with clip type closepins. pressed connections onto new element , secured screws and presto... All too simple and in less then 15 minutes.
Reading previous reviews was quite helpful
Was this helpful?
Thank you for voting!
element broke, oven wouldn't heat - still doesn't
1 person found this instruction helpful.
  • TESS from BOSWELL, PA
  • Easy
  • Less than 15 mins
  • Socket set
first husband removed the bolts unplugged old element wires -plugged in new element wires and but in bolts - unfortunately the oven still doesn't work not sure if element is bad or wiring, need professional help
Was this helpful?
Thank you for voting!
Heating element was not working in an old (50+ years old)GE electric oven
1 person found this instruction helpful.
  • Michele from Dayton, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Replacement of the heating element only takes a few minutes...First, turn off the breaker/fuse to the stove, then just remove two screws , pull out the two connected wires to expose the connections, hook them up, and replace the screws to the cover plate. The connection/cover plate can be hinged or not hinged. Make sure you order the co rrect one. We ordered the wrong one at first, but were assisted by the returns dept. and received the correct one in 2 days. Great customer service, thanks partsselect.com!!
Was this helpful?
Thank you for voting!
Tenant broke bake element
1 person found this instruction helpful.
  • John from Muncie, IN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the two screws, pulled out old element, installed new element, and reinstalled screws.
Was this helpful?
Thank you for voting!
burnt element
1 person found this instruction helpful.
  • Brian from Iron River, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
.g. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...)
Was this helpful?
Thank you for voting!
Old element burned in half
1 person found this instruction helpful.
  • Christine from Covington, LA
  • Really Easy
  • Less than 15 mins
  • Socket set
I turned off the power going to the stove, unscrewed the 2 screws, plugged in the 2 inserts, put the 2 screws back and PRESTO!!!!
Was this helpful?
Thank you for voting!
Bake Element went out..flamed out pretty big light show when it happened
1 person found this instruction helpful.
  • Don from Martin, TN
  • Easy
  • Less than 15 mins
  • Socket set
The job went over without a hitch, only probably didn't get the correct part first go around, but after getting the right part everything went very easy..Just a couple of screws where the elment goes in and 2 wires to plug back into the new element, after that everything was good to go!!
Was this helpful?
Thank you for voting!
The element on our three year old stove stopped working...this was the bottom bake element.
2 of 4 people found this instruction helpful.
  • shawn from port richey, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was surprisingly simple. All I had to do was shut the breaker off to the stove(safety first). Next open the oven door and use a flashlight just to help you see,and unscrew the two screws holding the element in place on the back stove wall. Next slide the stove away from the was to give yourself enough room to access the back of it(you may need to unplug it to get it out far enough. My model had a cover over the back that took six easy to remove screws. Once the back cover was off I could easily see where the element was plugged into, so i removed the wires from the end of the element(just female terminals slipped over the end) i then went back to the front of the stove and pulled to element out.

To install the new one...just guide the two ends throgh the back of the stove...install the two screws to hold it in place...go to back of stove..plug in wires(they were diff sizes so you couldnt mess it up) and put the cover back on..plug in oven..slide it back..and try it out...its that simple
Was this helpful?
Thank you for voting!
burned out
1 of 2 people found this instruction helpful.
  • David from Woodbridge, VA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
My dealer was unable to find the part even with a model number. Your accurate drawings allowed me to select correct part. It was a perfect replacement in every way and cheaper (by $10) than the dealer. Also quicker.
Was this helpful?
Thank you for voting!
Surface Element/burner had to be replaced
1 of 2 people found this instruction helpful.
  • Natalie from Harleysville, PA
  • Really Easy
  • Less than 15 mins
First, I removed the burner from the box and plastic bag. Second, I pushed the burner into the socket and that was it.
I also want to comment on how easy the ordering process was. I ljust love this website. All you have to do is type in the model number and up comes all of the parts associated with the appliance. My order shippe d the next day and I had unit within 2 days. Also, the part cost $42.00 with shipping. My local parts place was $48.00, so I wound up saving $6.00 and did not have to leave my home to buy it. I will definetly use this site again.
Was this helpful?
Thank you for voting!
8" stove element stopped working
1 of 2 people found this instruction helpful.
  • Michael from Standish, ME
  • Really Easy
  • Less than 15 mins
Everything was very easy: identifying the right part was very easy on the website, the part came quicker than I expected, and my wife replaced the stove element before I even got home from work. She just pulled the old one out like she would to clean the top of the stove, and put the new one back in. Have had several awesome cups of co ffee since the replacement.
Was this helpful?
Thank you for voting!
Bake element broken
1 of 2 people found this instruction helpful.
  • Charles from Damascus, MD
  • Easy
  • Less than 15 mins
  • Wrench (Adjustable)
Before ordering, I took the element out to make sure I could do it. A flashlight was helpful.

I flipped off the circuit breakers to the stove, removed the racks and lifted off the oven door. Not having a nutdriver or socket set, I used a 6' crescent wrench to remove the two screws which hold the element to the back of the oven . I carefully pulled the element out until the spade connectors to the wires were exposed. I wiggled the connectors apart. I had pliers handy, but didn't need them.

I connected the new element to the wires and gently pushed the two connected prongs through their holes, trying not to disturb the insulation. I put a little WD-40 on the screws so they would go in easier. After tightening the screws with the crescent wrench, I replaced the racks and door. I flipped the circuit breaker back on and reset the clock. It works as good or better than new.
Was this helpful?
Thank you for voting!
All Instructions for the JCSP31WV2WW
76 - 90 of 340