- Home
- JCBS64BK2BB
- Instructions
JCBS64BK2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
bakeing element burned out
0 of 1 people
found this instruction helpful.
-
Bob from Surry, VA
- Really Easy
- 15 - 30 mins
-
Screw drivers
Removed to screws on bracket and sliped the element out. Inserted new element and installed bracket and two screws.
Was this helpful?
Thank you for voting!
The bottom burner melted
0 of 1 people
found this instruction helpful.
-
Linda from Virginia Beach, VA
- Easy
- 15 - 30 mins
-
Pliers
First we removed the screws inside the oven. Next, the oven backing was removed by unscrewing one side and one bottom bolt which exposed the clips for the burner. The clips were removed from the old burner. The old burner was pulled through the fiberglass protection and out of the oven. The new burner was inserted into the oven and the
... Read more
prongs were pushed through the fiberglass protection. The screws inside the oven were reattached. The clips were attached on the outside of the oven. The backing was slid into the right holding piece and the bolts on the left and bottom were attached.
Read less
Was this helpful?
Thank you for voting!
F2 error when oven was heating up, along with a beeping noise and then it shut off
0 of 1 people
found this instruction helpful.
-
Lori from Paris, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Unplugged oven, turned off breaker, took cover off back of oven, removed old sensor by disconnecting in back of oven and undoing screw inside oven. Pulled old one out replaced with new took 15min. Cost me less than $20. Parts Select rocks! Even received part in two days with standard shipping!
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
F2 error code
0 of 2 people
found this instruction helpful.
-
jud from gatesville, TX
- Really Easy
- Less than 15 mins
-
Nutdriver
Really easy fix. Unplug oven. With a 5/16 nut driver take the 5 screws out of the center long tin cover and remove. Unplug little white temperature sensor plug located between broil heating element. Open oven door and remove one screw holding temp. sensor using same nut driver and simply pull out old sensor. Install new sensor. It's tha
... Read more
t easy. No more f2 been working like a champ!!!
Read less
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
Drawer glider broke about a year ago.
-
loma from Neah Bay, WA
- Easy
- 15 - 30 mins
-
Screw drivers
My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online a
... Read more
nd found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker
Read less
Was this helpful?
Thank you for voting!
The oven temperature could not be controlled
-
Keith from Annapolis, MD
- Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Disconnect the range from the mains. Open the door. Remove the single screw holding the temperature sensor - this is located on the back wall on center and is screwed to the broiler mounting plate. Remove the four screws holding the boiler element and allow it to hang down on the wire; this exposes a space to feed the wire through later.
... Read more
Now move to the back of the range and remove the six screws that hold the central cover plate. Now push the insulation to up out of the way and you can disconnect the temperature sensor, pull it out through front, insert the new one and connect it. Reassemble in the reverse order. Mine worked perfectly!
Read less
Was this helpful?
Thank you for voting!
Total Burn Out Of Original Broiler Element
-
richard from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first.
... Read more
Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.
Read less
Was this helpful?
Thank you for voting!
Oven would not reach bake temp.
-
Thomas from Rogersville, TN
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. R
... Read more
emoved the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.
Read less
Was this helpful?
Thank you for voting!
Oven slow to heat up
-
Joe from Harkers Is., NC
- Easy
- 15 - 30 mins
-
Nutdriver
Removed oven door. Removed 2 screws from heat sensor on rear upper wall of oven. Pulled unit out to access rear of unit. Removed six screws on shield on back of unit. Dis connected heat sensor wire and pulled old sensor through from inside of oven. Feed wire of new sensor through from inside and plug in. Everything in reverse. I also had
... Read more
the gas(propane) company come out and check the pressure coming out of the "low pres." regulator. It was low, they changed the regulator.
Read less
Was this helpful?
Thank you for voting!
Bake element not working
-
Rodney from Chambersburg, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 day
... Read more
s. excellent service. Thanks
Read less
Was this helpful?
Thank you for voting!
Replacment of burner control switches
-
Judith from Keezletown, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this helpful?
Thank you for voting!
element burnt out
-
don from protection, KS
- Really Easy
- 15 - 30 mins
-
Nutdriver
ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking
Was this helpful?
Thank you for voting!