- Home
- JCBS64BK2BB
- Instructions
JCBS64BK2BB General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Heat element died
2 of 3 people
found this instruction helpful.
-
Andrea Hines from ELGIN, AZ
- Very Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Very easy to replace. So easy even a man can do it.
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 people
found this instruction helpful.
-
RICKEY from MONTROSE, NY
- Easy
- Less than 15 mins
-
Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
Was this helpful?
Thank you for voting!
Burner spontaneously cycled without knob activation
2 of 3 people
found this instruction helpful.
-
Anil from Milpitas, CA
- Easy
- Less than 15 mins
-
Screw drivers
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Read less
Was this helpful?
Thank you for voting!
Burner burned out
1 person
found this instruction helpful.
-
Daniel from Norborne, MO
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Very easy. Unpluged range from outlet, took two screws from the front under side of the range top, raised cook top up, took off four wires from burner, removed two screws than holds burner on cook top, replaced with new burner, installed two screws that hold burner in place, installed the four wires to burner, lowered cook top back into
... Read more
place replaced two screws that hold cook top down, pluged back into outlet. DONE!
Read less
Was this helpful?
Thank you for voting!
Burner didn't go on
1 person
found this instruction helpful.
-
Mike from Hatfield, PA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Turned off juice
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble
Pulled stove from wall
Unscrewed 2 screws to loosen range top
Lifted n propped top
Unplugged 4 wires
Unscrewed burner assembly
Installed burner-reversed steps to reassemble
Was this helpful?
Thank you for voting!
burner didn't work
1 person
found this instruction helpful.
-
Richard from Coon Rapids, MN
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
lift stove top, 2 undermount screws. Then unplug 4 wires, I did them 1 at a time plugging into new burner as I go so I wouldn't screw up. Take 2 screws out of old burner to stove top, # all around circle put screws in same # on new burner.Done Good experience all the way around. Order delivery and install
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people
found this instruction helpful.
-
Melvin from Portland, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
Oven would not heat up
1 person
found this instruction helpful.
-
MICHAEL from MORROW, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.
Was this helpful?
Thank you for voting!
Burner no longer heats
1 person
found this instruction helpful.
-
Anthony from Apopka, FL
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Remove two screws with nut driver that holds range top down. Turn off breaker or unplug before lifting top. Brace top with 2x4. Take picture with cell phone just in case. Orient replacement part with old burner. Remove one wire at a time and install on new burner in corresponding correcting terminal. be sure they are snug. Drop top insta
... Read more
ll nuts . Test! Done! I am not an electrician!!!!!!!! Please do not publish !!!!
Read less
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person
found this instruction helpful.
-
Ron from SAN TAN VLY, AZ
- Very Easy
- Less than 15 mins
-
Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
would not heat
1 person
found this instruction helpful.
-
Mark from SARASOTA, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Did the repair just like the video shows.
Was this helpful?
Thank you for voting!
Broiler Unit Failed
1 person
found this instruction helpful.
-
William from BOYERTOWN, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.
Was this helpful?
Thank you for voting!
oven racks old and ugly
1 person
found this instruction helpful.
-
Claudene from ORCUTT, CA
- Very Easy
- Less than 15 mins
1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired
Was this helpful?
Thank you for voting!
The lower,BAKE, element had burned in half almost causing a fire.
1 person
found this instruction helpful.
-
Joseph from DIAMOND SPGS, CA
- Very Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the o
... Read more
ven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.
Read less
Was this helpful?
Thank you for voting!
The bottome heater element of my oven burned out.
1 person
found this instruction helpful.
-
Mary from ALOHA, OR
- Really Easy
- 15 - 30 mins
-
Pliers
I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to th
... Read more
e range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!
Read less
Was this helpful?
Thank you for voting!