EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP80CJ1CC General Electric Range - Instructions

All Instructions for the JCBP80CJ1CC
106 - 120 of 463

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Grease spilled on old gasket----gasket hardened
5 of 9 people found this instruction helpful.
  • Delores from Rocksprings, TX
  • Really Easy
  • Less than 15 mins
Simply pulled old gasket from door and pushed new gasket clips into existing holes and tucked in ends at bottom of door.
Was this helpful?
Thank you for voting!
When you touched any button on the controls LOC on appeared.
3 of 3 people found this instruction helpful.
  • Roger from HUNTSVILLE, AL
  • Very Easy
  • Less than 15 mins
Talked to parts select tech after ordering the control board. Tech advised me that he felt the range could be repaired without installing any parts. Advised me to contact manufacture tech support and explain the problem. I did to find that the child safety lock was on, probably from cleaning and touching too many buttons at once while whi pping surface. Told me to hold down + and - at the same time for three seconds and it was fixed.
Parts select tech had told me don’t worry the parts are guaranteed so I called for a RMA and returned the parts for a refund. Thanks Parts Select, y’all are real professionals and that is greatly appreciated.
Thank you all.
Was this helpful?
Thank you for voting!
Switch was not turning off range indicator light
3 of 3 people found this instruction helpful.
  • Charles from PORTLAND, OR
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Pulled stove out and unplugged. At the rear of the range there were 4 faster. Used a nutdriver piece in an electric drill. Pulled off the cover and located the switch. At the front of the stove, I removed the knob and unscrewed two screws releasing the switch. I undid and replaced each wire connector one-by-one to avoid any wrong connecti ons. Replaced and secured the switch and replace the back panel. All secured, power on and fixed! Easy repair, but something that had been put off for a year!
Also follow the installation videos from PartSelect - very helpful!
Was this helpful?
Thank you for voting!
Incorrect oven temperature due to defective temperature sensor.
3 of 3 people found this instruction helpful.
  • Anthony from FARMINGVILLE, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Performed repair using a video for reference.
Was this helpful?
Thank you for voting!
old oven racks were ruined from self-cleaning oven
4 of 6 people found this instruction helpful.
  • Joan from Holt, MI
  • Really Easy
  • Less than 15 mins
My exact model number did not appear in the listings, nor were the oven rack measurements clearly stated in items offered. I sent an email to customer service, received an immediate response with the correct answer (re: which part would fit my oven), ordered this item, and had a shipment arrival within days. The racks are a perfect fit, and they look great. The price is less than any other site I investigated.
Was this helpful?
Thank you for voting!
drwer slide under stove broke off.
3 of 4 people found this instruction helpful.
  • paul from sewell, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
recieved part the next day. looked different but I followed instructions and the part worked perfect.
Was this helpful?
Thank you for voting!
Did not have a problem, just need an extra oven rack.
3 of 4 people found this instruction helpful.
  • Catherine from Bethel, CT
  • Really Easy
  • Less than 15 mins
Placing the order was very easy. Shipping was fast and excellent packaging. Thank you very much!
Was this helpful?
Thank you for voting!
Burner food on racks
3 of 4 people found this instruction helpful.
  • John from Metairie, LA
  • Really Easy
  • Less than 15 mins
Nothing really rocket science here. The oven racks had burned on food, and I just replaced the racks..... slide out the old and slide in the new. Done !
Was this helpful?
Thank you for voting!
The temperature indicator light on the oven was broken.
3 of 4 people found this instruction helpful.
  • Jewel from Nacogdoches, TX
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I removed the control panel by removing 7 screws and replaced the light indicator and lens.
Was this helpful?
Thank you for voting!
burner not work
3 of 4 people found this instruction helpful.
  • SILVIA from Midlothian, TX
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
Fue muy facil desconectar primero la estufa despues quite los tornillos de la parte superior detras de la estufa, desconecte un cable del switch y lo conecte en el nuevo despues el siguiente hasta conectar todos los cables en el nuevo switch. Lo mejor es desconectar uno por uno para mo mesclar los cables , despues removi el switch de la e stufa y puse el nuevo , puse las partes de regreso y listo conecte la estufa t revise si funcionava el quemador y listo sin ningun problema.
Was this helpful?
Thank you for voting!
Broiler element was bad
3 of 4 people found this instruction helpful.
  • David from LENOIR CITY, TN
  • Easy
  • 15 - 30 mins
  • Nutdriver
1st and formost, unplug the range from the outlet or shut th breaker off (Ranges are on a seperate breaker). Detach 2 wires on the back of the range connected to the element. Remove three nut screws inside the oven holding the old element in place . 1 on the top and 2 at the back of the oven. Now just reverse this procedure to install the new element and your all done.
Was this helpful?
Thank you for voting!
Broken interior oven window
3 of 4 people found this instruction helpful.
  • George from Bowie, MD
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
It took a bit of head scratching to remove the oven door. I had read another user saying he'd removed the hinge screws unneccessarily, so I left them alone. I eventually was able to locate the locks on each hinge. Once they were disengaged, it was a simple matter to lift off the door. After that, I removed all the screws (except the h inge screws) and took the door apart. Once it was disassembled, I found two loose triangular pieces, about 1 1/2" long. I later discovered these were spacers for the two top srews. They were placed on end, and the top screws passed through them. All in all, a relatively simple repair, which absolutely amazed my wife, landlord, faily, etc.
Was this helpful?
Thank you for voting!
Burner Was Not Working
3 of 4 people found this instruction helpful.
  • Roland from Miami, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the two screws that hold the range top down. Lifted up yhe range top and propped with a stick. Proceeded to mark the wires connected to the old burner so that the new one would be connected correctly. Removed the wires and then the two brackets that hold the burner in place. Removed the old burner and installed the new one. C onnected the wires and resecured top to base. Turned on the current and it worked beautifully.
Was this helpful?
Thank you for voting!
the small burner was burnt out
2 of 2 people found this instruction helpful.
  • Jack from Columbiaville, MI
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
after removing the two screws that are just inside the oven, I propted the top open with the box that the part came in. I drew and labeled the wires as I took them off using a color coding. next I removed the two clips that held the burner in place and marked on the new burner exactly where the clips were attached. Replacing the clips was possibly the hardest part of the whole operation. When you replace the burner, don't forget to replace the insulation pad that is stuck one the metal where the conections are. I missed this and had to reopen the stovetop and slid it on after I was finished. Otherwise it went pretty smooth.
Was this helpful?
Thank you for voting!
Element would not respond to changes in temperature setting
3 of 5 people found this instruction helpful.
  • douglas from chance, VA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Turn off power to cook top. Remove 2 screws that hold the cook top to countertop. Lift complete cook top from counter and place diagonally across opening. Remove 10 screws that hold glass top to the component cabinet. Make a diagram of wiring to element. Disconnect wires. Remove 2 mounting brackets from bottom of old element and posi tion them on new element and screw tight. Wire new element as diagrammed earlier. Replace glass top on component cabinet and reinstall 10 screws. Place unit back into counter opening and secure with 2 straps. Turn power back on. Stand back and enjoy your accomplishment.
Was this helpful?
Thank you for voting!
All Instructions for the JCBP80CJ1CC
106 - 120 of 463