EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JCBP62DP1WW General Electric Range - Instructions

All Instructions for the JCBP62DP1WW
121 - 135 of 195

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven continued to get F2, F3 and F5 error messages when ovewn got hot
  • Ralph from Redding, CA
  • Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
This repair was quite a bit more difficult then what had been described on the web site. First off, I have a double wall oven that is built in. Sliding it out of the cabinet was difficult and because oven was hard wired, I had to disconnect the actual wiring from the oven back. . Positioning the oven and allowing for it to rest on a s upport bench was the most difficult part The oven is heavy. Eventually, removing the back and top panels of the oven revealed the sensor connection. I was then able to feed it through the oven and reconnect all the wiring harnesses.. Getting the oven back in the cabinet was equally a challenge. But it did seem to fix the problem with over heating.
Was this helpful?
Thank you for voting!
Wires to attach to bake element retracted into stove body
  • Michael from Hamden, CT
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers
I had to remove the back panel on the stove to free up taped wires to get more length.
Was this helpful?
Thank you for voting!
Element was burned out
  • William from Franklin, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Disconnected the plug from the receptacle; removed the 2 screws holding the element in place at the rear of the oven; removed the support bracket at the front (also 2 screws); removed the panel on the back of the range; pulled the wire clips off the element (had to replace one of them); slid the new element in place; reconnected the wires and fastened the element in place; reattached the support bracket and rear panel ... With the assistance of my wife (extra hands) this was an easy job!
Was this helpful?
Thank you for voting!
Drawer glider broke about a year ago.
  • loma from Neah Bay, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers
My wife could open and close the drawer without too much difficulty, but occasionally, it would not close properly and she would have to empty the contents do could alaign it properly to close. The last time she was talking about buying a whole new drawer. I asked her what the part looked like, as I never to fight with it. I went online a nd found the part for $1.16 plus shipping at $8 plus. It was well worth the time and effort, and I now have a happy wife. Paul Parker
Was this helpful?
Thank you for voting!
Replacment of burner control switches
  • Judith from Keezletown, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
I watched your video on the subject and followed it exactly. It explained everything I needed to know. The hardest part was CLEANING under the stove once I pulled it out from the wall!
Was this helpful?
Thank you for voting!
element burnt out
  • don from protection, KS
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
ordered part shut electricity off took out 2 screws took of connectors put in new element replaced connectors replaced screws turn on elec started cooking
Was this helpful?
Thank you for voting!
Bad Burner
  • Roosevelt from Waggaman, LA
  • Really Easy
  • 15 - 30 mins
I simply removed the 2 anchor screws in front of the stove and wrote down the wiring order on the instillation diagram, removed the old burner, removed the two studs, made sure they were installed on the right numbers place them in the new burner, wired the new burner, placed the springs respectively. Placed them in the correct holes in the frame to be sure that the burner was aligned properly. Put the washers on the studs and replaced the frame screws, lowered the cook top and returned the screws to lock the cook top in place.
Was this helpful?
Thank you for voting!
broken light socket
  • James from Monterey, TN
  • Easy
  • 15 - 30 mins
  • Nutdriver
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Was this helpful?
Thank you for voting!
A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range
  • Ruth from Potosi, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers, Wrench set
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!
Was this helpful?
Thank you for voting!
Getting the right stove model number and part number
  • Gerald from San Diego, CA
  • Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Difficulty was in determining the right model number and part number of a switch. Noted that the left front burner came on when the switch for the left back burner was turned on. By inspection I found the left front burner switch had become faulty by actually hearing an electric arc in the switch and smelling the oder in the switch. With help from the person I called I was able to determine that the Model Number on the actual stove was wrong. It had an extra 0 between the W and F which she said was a common error in the GE model number. I then gave the switch number I found on the switch to the contact person and she was able to verify the right part number. It was relatively easy to replace the switch by taking off the back upper plate then taking off two screws that held the switch to the stove. The part came quite quickly once ordered. Sears repair wanted $75 just to diagnose then the cost of the part. I got the switch for $69.
Was this helpful?
Thank you for voting!
Oven would not reach bake temp.
  • Thomas from Rogersville, TN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Used the TS guide, because I had no idea what the problem was. That was easy step by step. Thanks. Gave me a list of two parts that could fix the problem. Picked the higher percentage part (97%). Followed the simple install instructions and it was successful. One problem I did encounter was the two wires that it connected to were short. R emoved the back center plate to gain access to the wires. I was able to extend them enough to make the connections to the bake element. If not for that the repair would have only taken maybe 10 minute's.
Was this helpful?
Thank you for voting!
Oven Sensor Replacement
  • Barbara from Edwardsville, IL
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
The part was just like the old one and would have been an easy fix except our range suffered from a lighting hit. The clips had melted together. Called a dealer and asked about a new wiring harness. He said in those cases just cut the clip off and hard wire with wire clips,or firecrackers. We used wire nuts and taped all together and the oven works just great. Nothing is ever as easy as it should be.
Was this helpful?
Thank you for voting!
burn out switches
  • Thomas from Hinesville, GA
  • Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Pull stove out from the wall unplug it remove the old switches and replaced them withe new one. they work just fine.
Was this helpful?
Thank you for voting!
Right front burner not getting hot
  • Cory from Honesdale, PA
  • Easy
  • 30 - 60 mins
  • Nutdriver
After searching the internet for a cause for the burner not getting hot it looked as though it was the burner switch. I ordered the switch and installed it. Behold it still did not work. I then ordered the burner, installed it and it worked. So I had a 50/50 chance as to which part was the problem. This was my first stove repair and I found it easy to do. Finding something to hold up the ceramic cooktop took the most time. I cut a piece of wood to prop it up while I replaced the burner.
Was this helpful?
Thank you for voting!
Old dishwasher rack and silverware rack
  • Anne Marie from Andover, MA
  • Really Easy
  • Less than 15 mins
The whole process was very easy! I just got the model number and bought a new rack and silverware holder on,one. There was no assembly needed so I just popped them in and replaced the old ones! Very easy to do!
Was this helpful?
Thank you for voting!
All Instructions for the JCBP62DP1WW
121 - 135 of 195