- Home
- JCBP62DP1WW
- Instructions
JCBP62DP1WW General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Element went bad
0 of 1 people
found this instruction helpful.
-
Steve from Blue Hill, NE
- Really Easy
- 15 - 30 mins
-
Screw drivers
turned electricity off, removed element using a screwdriver had to take the back panel off, attached new element put stove back and tried it out and it worked probably 20 minutes. Also need to comment that was totally shocked how fast the element was shipped to me, ordered the part in the p.m. and it was here not the next day but the next
... Read more
....awesome
Read less
Was this helpful?
Thank you for voting!
The element started to spark and actually broke into two pieces.
0 of 1 people
found this instruction helpful.
-
Joe from Austin, TX
- Very Difficult
- 15 - 30 mins
-
Nutdriver, Pliers
I have a GE Profile oven and the heating element on the bottom broke in two. I found the part on your website very easily. It was easy to see that I had the correct part. I ordered the new element and it came in about three days. I easily took off the old element, but I was really surprised because the new one didn't fit. The heating
... Read more
element itself was the correct size, but the holes didn't quite match up. As a matter of fact I had to take some tin snips and expand the hole at the back of the oven. That was the only hard part, but it was really difficult to lean in that far without putting too much weight on the door. Anyway, I opened the hole about an inch more, plugged it in, and now it works perfectly!
Read less
Was this helpful?
Thank you for voting!
burner was inoperative
0 of 2 people
found this instruction helpful.
-
bryan from cocoa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
verified switch operation , checked continuity of burner element found open ordered new part and installed next day
after extremely fast
service from partselect thank you
after extremely fast
service from partselect thank you
Was this helpful?
Thank you for voting!
light keep burning out in oven.
2 of 8 people
found this instruction helpful.
-
john from Mc Kees Rocks, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver
Remove the door. Just open a little and pull up. Removed racks. Removed 3 screws with nutdriver. Pulled out housing. Disconnected 2 wires. Assembled new housing with with bulb receptacle and gasket. Reconnected wires and crimped a little to make them snug. Pushed housing back into hole. Put 3 screws back in, inserted bulb and cover. Slid
... Read more
door back on and done. 30 minutes at most.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner not heating.
1 of 5 people
found this instruction helpful.
-
Jack from Greensboro, GA
- Really Easy
- 30 - 60 mins
-
Screw drivers
Isolated to control switch.
Replaced
Replaced
Was this helpful?
Thank you for voting!
eye wouldnt come on
0 of 2 people
found this instruction helpful.
-
daniel from valentines, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in
Was this helpful?
Thank you for voting!
Light burnt out.
2 of 8 people
found this instruction helpful.
-
Roscoe G from ROCHESTER, NY
- Very Easy
- Less than 15 mins
Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.
Was this helpful?
Thank you for voting!
Total Burn Out Of Original Broiler Element
-
richard from Palm Coast, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Remove lower drawer and contents. Unplug unit. Tilt range on its back for easy access. Tie open oven door to forward legs with sturdy rope. Use small socket to remove 2 back screws and 2 forward element hanger screws. Detach broiler element connections from wire clips(2). Insert new element, attach 2 new connections to clips first.
... Read more
Install back socket screws. Install front socket screws for element hanger. Slide in oven shelves. Release oven door rope. Lift range to normal position. Replace lower drawer. Plug 220 in. Test oven element then broiler.
Read less
Was this helpful?
Thank you for voting!
Baking element burned out.
-
Gary from Port Gibson, MS
- Really Easy
- 15 - 30 mins
-
Nutdriver
Turn off power to oven. Removed the rack. used a 1/4" nut driver and removed the two screws holding the element to back of oven. Slid the element out, unhook the two wires clipped to the end of the element. Replaced it with the new element, installing it in reverse. Took about 15 min. Rememer to turn off power to oven before attempting t
... Read more
o work on it.
Read less
Was this helpful?
Thank you for voting!
bake element needed to be replaced
-
Bernadette from Coatesville, PA
- Easy
- 15 - 30 mins
-
Socket set
My oven is wired into the wall so I had to cut the power off at the fuse box. The hardest part was pulling the stove/oven away from the wall to see if it was a simple plug in or wired in. I lifted bottom drawer out so I could get leverage and lifted the entire unit so I could put the front feet on the soft pads. It slid away from the wa
... Read more
ll easily. I found a socket that fit the screws on the plate holding the broken element and unscrewed it, saving the screws. A gently tug on the element pulled the attached ends through the hole. The tip of the ends were attached to the wall wiring by a small sliding metal clip. I carefully pulled the ends apart. One was hard to get apart to I had to push it with the tip of a knife. Once the old was off the new was super easy to put back on. Side the tips to the clips, screw the plate in place and push the oven back in place. Flip your fuses and turn on the oven. Yeah!
Read less
Was this helpful?
Thank you for voting!
Bake element buned and broken
-
Charles from Pittsburgh, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
The repair was somewhat easy. The replacement elements are pushon type. The only thing is that the G.E. Hotpoint wire on the right side of the bake element is short. Be extra careful to not have it go back into the back oven wall or you will have to take the back cover plate (Pull out the range, remove the back cover using a nut driver or
... Read more
a magnetic tip srewdriver with the bit removed works[Wires are right there]. This is as easy a job as can be.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
broiler element burned completely out
-
Raymond from Highland, MI
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Moved stove out away from wall .Unplugged stove, turned gas off. Unit is a dual fuel convection. Burners are gas, oven is electric. Removed 4 screws from back shield and exposed the 2 electrical leads connected to broiler element. Disconnected the electrical .Inside oven I removed the front bracket holding element in place, then removed t
... Read more
he 2 1/4 screws in the back holding element in place. placed new element in and finger tightened the 2 screws, next I installed the front bracket and finger tightened those. I then snugged the rear screws in followed by the front. I went to the back and reconnected the 2 electrical leads. Replaced back shield and plugged unit in and turned gas back on.Caution; Make sure your gas line is flexible before moving your stove out to far. Repair was very easy
Read less
Was this helpful?
Thank you for voting!
Bake element not working
-
Rodney from Chambersburg, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed element with 1/4 " nut driver, unhooked element,started to install new element and discovered the wires were too short and had to remove cover on the back to replace wires on the new element. The wires on my range were not as long as the ones showed on the video.It was still an easy repair and the delivery time was less than 2 day
... Read more
s. excellent service. Thanks
Read less
Was this helpful?
Thank you for voting!
Burner Would Not Turn Off
-
BILLY from WEBSTER, FL
- Really Easy
- 30 - 60 mins
-
Nutdriver
Replace control switch
Was this helpful?
Thank you for voting!
one leg of the terminal block was loose and overheated under load.the terminal block melted and could have caused a fire.
-
brendan from lebanon, NH
- Easy
- 30 - 60 mins
-
Pliers, Screw drivers, Socket set, Wrench set
I took a picture of the setup and damage . I then disconnected the burnt wires and replaced the wires . Then I installed the new terminal block and connected the wires to the proper positions. The reason for the failure was that the delivery people didn't tighten the cord when they installed the stove . I would check the connections per
... Read more
iodically as to avoid another situation like this .
Read less
Was this helpful?
Thank you for voting!