JBS86SP3SS General Electric Range - Instructions

My oven bake element melted one day. I had my husband replace it and for a short while it worked. Then it quit but then our broil element would not shut off. My husband said that it might be the heat sensor. We checked here in town and that element cost over $80. Since we have order from Parts Select before we decide to do so again. When ... Read more we received the heat sensor my husband replaced it taking out the original heat sensor. This did not work as the broil element still would not turn off. I call the repair man and I found out that the initial melt down of the bake element also effected the main circut board that had to e replaced.

First turned off power at breaker box. Pulled stove out to remove the half dozen hex screws on the back panel.(some nuts were stripped)Removed old oven sensor inside oven held by one hex screw and replaced it with the new part. Oven works great now! Repair job was done by husband Mike.

Replacement was not very difficult but did require some time. I unscrewed the two areas holding the cooktop in place, slightly lifted the unit up then slid it over a bit to remove from the back area. This unit has the burners affixed to the underside of the cooktop using brackets. Instead of working underneath the raised unit I decided ... Read more to unhook the cabling in the back and fully removed the cooktop. I moved the cooktop to a flat surface and then I was able to easily remove all of the screws holding the brackets to the burners. I moved all the hardware to the new unit and replaced the cooktop. I was able to dissemble the unit myself but it was helpful having an extra set of hands when it was time to put the new unit in place. Tools used were a socket wrench and a screwdriver.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

First; turn off breaker to stove.
Second; remove two Phillips head screws that hold the top on, located in front, underneath, will have to open the oven door to see.
Third; prop the top up.
Four; disconnect wire clips of old element.
Five; plug in new wire clips of new element.
Six; unprop the top and realign ... Read more the top.
Seven; replace the two Phillips head screws to secure the top, then close oven door.
Eight; turn breaker back on.
Done and Back in Action! You Can Do This!

Disconnect power, then remove racks from oven, locate heat sensor by the broiler element. Use ratchet with extension and correct socket to remove the bolt directly under the heat sensor, pull the sensor out till you see the plug, disconnect the plug and then connect new sensor to it push wire back thru and then rebolt the new sensor on, ... Read more thats it...

Very simple. Remove one screw and carefully pull the sensor until you see the connection point. Remove the old one and snap the new one in and guide the wire back and reassemble the screw. Be sure to remove the oven door for easy access.

Unplug stove.2 screws out ,lift top ,disconnect bad element, connect new element, put top down .2 screws in .plug stove back in...EASY PEASY

Ordered the part, turned off the circuit breaker, test to see that power is off, take a 5/16” nut driver, and remove the 2 screws under the front of the stove top, then lift the top up and hold it up with an old 2x4 about 24” long. All the connections are plug and play, so I took some needle nose pliers, to pull all 5 wires off of the bur ... Read more ner. Then all that’s left to do is remove 3 spring clips. That was easily done by inserting a flat screwdriver into the back of each clip and pry them out. It ended up being a very easy fix. There is Utube videos to show you how to do it.

Unplug stove first. Raised the stove top and propped up useing wooden spoon and wife assistance holding up. Pay attention to spot brackets hand to top. Removed sheet metal screws from bracket clamp holding burner in place. Removed one extension bracket from old burner and transfeered to new burner. Removeing one bracket clamp allows the ... Read more other one to act like a hinge and make for easy removal and replacement. Back of burner had corresponding numbers which made it easy to replace brackets in same place as old. I carefully take one electrical wire at a time from old burner and transfeered to the new burner. Replaced burner same way it came off.

unplug stove first...take back of stove off to get to burner switch remove wires colors coded.. get new switch put wires on the same way.plug stove in test burner...very simple to replace.and save $$$$$$$$

I changed out the sensor and still same problem. Change out Thermosat and still same problem.
I call the help number and emailed the help but I got nothing but have to many calls because of the virus situation.
Still need help.
I’m an electrician and I don’t want to call a service technician and pay that big bill.
... Read more Can anyone there help me out, if so please call.
Ike Stanton
678-525-6644

This should have been a very easy fix. But, as I tried to pull out the old temperature sensor, the wire would not come out. I was afraid to pull too hard because I did not want to break the wire. So, I coxed it out easily until I could see the plastic connector. Then, the old wire pulled free from the connector leaving the end of the c ... Read more onnector inside the back of the oven. I then had to fish the end of the wire around with the piece of wire through the very small hole in the back of the oven. Once I got it close to the hole, I was able to grab the connector with some needle nose plyers. Connecting the new sensor and reinstalling everything was easy and the oven now works just fine.

I just followed the instructions on the link provided with the part

Pulled the oven out and unplugged it. Removed five screws and the back cover. Disconnected the electrical connection. Removed one screw and pulled the sensor out. Installed the sensor and screw. Made the electrical connection on the back, replaced the cover and five screws. Plugged the electrical cord back in and tested the oven tem ... Read more perature compared to the setting. Worked great. My wife then made a small batch of muffins to test it out and they were good.