- Home
- JBS65RF1SS
- Instructions
JBS65RF1SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bad Line fault displayed on range clock
1 person
found this instruction helpful.
-
Vincent J Paola, from GREENWEL SPGS, LA
- Very Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
1. Unplug the range power cord from the outlet.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ... Read more ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
2. Moved range away from the wall and countertop.
3.Using a nut driver removed the 2 screws on each side of the removable panel on the back side of the control knobs and clock.
4. Using a phillips head screwdriver remove 2 screws on top side of the back side panel.
5. Usi ... Read more ng a nut driver remove 4 screws that secure the main control board in place.
6. Take photo of the wiring on the main control board if not color coded.
7. My control board, and the replacement board were both color coded with the color with the wire placement on the rear of the board.
8. Remove wires with needle nose pliers.
9. Using a hair dryer, heat the plastic control panel face plate that fits onto the front of the old control board.
10.With a putty knife carefully pry the face plate from the old control board.
11. Install the control board face plate onto the new control board.
12. Install the color coded wiring in place on the back side of the control board.
13. Replace the control board into the range, and install screws, and rear panel of the range.
14. Plug cord into outlet and test range for proper operation.
Read less
Was this helpful?
Thank you for voting!
Bake unit started on fire then cracked in half.
2 of 4 people
found this instruction helpful.
-
Sachin from Omaha, NE
- Easy
- Less than 15 mins
-
Socket set, Wrench (Adjustable)
We ordered the part from PartSelect and received it the next day. Didn't even have to move the range out from the wall. Just unscrewed the two screws on the back wall of the stove that hold the bake element in place with a socket wrench, then pulled the old bake element and wires out about 2-3 inches so we could disconnect the old bake
... Read more
unit. The element was kind of hard to pull out, but after you pull it from the wires, just plug in the new bake unit, push the wires back in and put the screws back in. Oven was up and working again!
Read less
Was this helpful?
Thank you for voting!
Bake unit caught fire and a 3 inch section burned away
1 person
found this instruction helpful.
-
Mark from Comstock Park, MI
- Really Easy
- Less than 15 mins
-
Socket set
Becuase of the fire we had used a chemical based fire extinguisher, which made a real mess in the whole main floor of the house. I removed the oven from the house and used a leaf blower to get rid of all the white chemical powder (like a baking soda of sorts). Once that issue was done, I removed the part in less than 5 minutes. Two scr
... Read more
ews to remove it and then unpluged the two wire clips from the back of the stove under the shield which also had 6 screws to remove. It took only 3 days to have a new one delivered and I installed it in less than 5 minutes. The oven works fine now. It took much longer to clean the house than fix the oven.
Read less
Was this helpful?
Thank you for voting!
Replacing handle spacer
1 person
found this instruction helpful.
-
Sherry from SAINT PAUL, MN
- Easy
- Less than 15 mins
-
Screw drivers
This one is simple. unscrew a portion of the door, install the spacer and screw back together. Worked well.
Was this helpful?
Thank you for voting!
The light inside the oven had burned out
3 of 7 people
found this instruction helpful.
-
Catherine from SEATTLE, WA
- Very Easy
- Less than 15 mins
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Read less
Was this helpful?
Thank you for voting!
Baking element broke
1 person
found this instruction helpful.
-
Veronica from PORT ORCHARD, WA
- Very Easy
- Less than 15 mins
-
Wrench set
Opened the box removed old element with socket put new one in tightened and voila ?? Just in time for thanksgiving ??
Was this helpful?
Thank you for voting!
THE FACE PLATE IS HARD TO GET OFF THE OLD CONTROL BOARD. USE A THIN KNIFE
1 person
found this instruction helpful.
-
Melvin from WEBSTER, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.
Was this helpful?
Thank you for voting!
Oven board went out
1 person
found this instruction helpful.
-
Jackie from TICKFAW, LA
- Very Easy
- 15 - 30 mins
-
Pliers
One wire at at time then used my razor blade to get front off stuck right back on
Was this helpful?
Thank you for voting!
Lower heating element broke and burst in flames
1 person
found this instruction helpful.
-
Heinz from Colleyville, TX
- Easy
- 15 - 30 mins
-
Nutdriver
On the website, the heating element looked exactly the same with same measurements as the old one. However, the part I received did not match. The screw holes where the element attaches to the back were wider apart and higher. Plus, the leads curved up instead of being straight.
Was this helpful?
Thank you for voting!
Replaced oven door gasket
1 person
found this instruction helpful.
-
Paul from JACKSONVILLE, FL
- Really Easy
- 15 - 30 mins
-
Screw drivers
Remove old stained gasket and replaced with new. Only $57.00!
Was this helpful?
Thank you for voting!
Plastic guide Broken
9 of 25 people
found this instruction helpful.
-
NICK from Vernon, CA
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
replaced Plastic Guides
Was this helpful?
Thank you for voting!
Bottom element fell apart
1 person
found this instruction helpful.
-
david from Cromwell, CT
- Easy
- 15 - 30 mins
-
Screw drivers
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. ordered the part and connected the element back to the two wires replaced the two screws plugged in the stove turned on the oven and we were back in business,
Was this helpful?
Thank you for voting!
Heating element literally blew apart during use one. We have no idea why,
1 person
found this instruction helpful.
-
Jon from Fort Worth, TX
- Easy
- 15 - 30 mins
-
Screw drivers
First, pulled out the old heating element and all the peices that were left after it fell apart. Since when you pull out the old one, the wires it connects to tend to recess back into the oven wall, I had to pull out the oven and take the back cover off in order to push the wires and connectors back through the receptacle in the oven. T
... Read more
his was really easy as you only have to remove 5 screws from the middle panel on the back of the oven rather than the entire oven back. Once the wires were back through, I just plugged in the new unit. The oven works just like new now. I'm sure I was able to save between $75 to $100 just for the service call by doing this myself.
Read less
Was this helpful?
Thank you for voting!
Oven heater coil burned out
1 person
found this instruction helpful.
-
David from Canterbury, CT
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed power plug- disconnected wire, removed cover over wires two screws, and removed old heated strip, held in by two screws inside of oven
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Slide in new coil installed two screws, connected two wires replaced guard over wires, plugged in stove, cooked a rubarb pie, success
Was this helpful?
Thank you for voting!
oven wouldn't heat
1 person
found this instruction helpful.
-
JEAN-C. from PARRISH, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver
removed two screws that hold the element in place and then removed the access rear panel it was much easier to disconnect the element than have to stick my head in the oven to gain access.time :15 minutes.
Was this helpful?
Thank you for voting!