- Home
- JBS65RF1SS
- Instructions
JBS65RF1SS General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
contracted broke the oven handle
2 of 2 people
found this instruction helpful.
-
Kathleen from NESCONSET, NY
- Really Easy
- 30 - 60 mins
Unscrewed the handle from the oven door and replaced same. Thanks for having a part for a 2015 appliance.
Was this helpful?
Thank you for voting!
Gizmo in oven that gets red hot when you bake had burned out.
3 of 6 people
found this instruction helpful.
-
B from Niceville, FL
- Easy
- 15 - 30 mins
-
Nutdriver
Gizmo = Bake Element held in place with 2 bolts inside of oven. Removing them only difficult because they are so deep in oven. I did not have the correct size nut driver so I started with my socket wrench then switched to putting the correct size socket on the end of a long screwdriver. After removing the 2 bolts fund element did not s
... Read more
lide out easily so went to back of stove and removed a metal protective cover. Found electrical lines secured to the ends of the element. Had someone hold element while I pulled each of the 2 loose - at which time bake element fell loose. Put new one in by reversing the process. That night wife set stove to Clean - and said best it has been cleaned in years.
Read less
Was this helpful?
Thank you for voting!
Broken rear drawer support
2 of 3 people
found this instruction helpful.
-
Jesse from Knob Noster, MO
- Really Easy
- Less than 15 mins
-
Nutdriver
Installed the new brackets at the back of the drawer with the 2 screws provided. The new rear mount design is much better than than the old side mount.
Was this helpful?
Thank you for voting!
My electronic control board went out so I could not use my oven. My oven light blew as well.
2 of 3 people
found this instruction helpful.
-
Stella from PADUCAH, KY
- Really Easy
- Less than 15 mins
-
Pliers, Socket set
I started with changing the bulb. I removed the small bracket that holds the glass cover over the bulb unscrewed the bulb and reversed to replace the bulb. To replace the control board I removed the top plate on the back of my stove took the small screw's out of the control panel and unplugged the wire's. Plugged the wire's into the right
... Read more
spots on the new control board and put it back together.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Burner spontaneously cycled without knob activation
2 of 3 people
found this instruction helpful.
-
Anil from Milpitas, CA
- Easy
- Less than 15 mins
-
Screw drivers
First I cut the circuit at the breaker, and then pulled the range from wall to access the access panel. This top panel was held with 4 screws and removable with a standard phillips head screwdriver.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
I then removed the 5 wire-crimped fasteners from the defective surface burner switch. (I first labeled these wires to ensure cor ... Read more rect placement to the new switch). There were an additional two screws behind the corresponding knob that needed to be removed in order to completely remove the old switch.
The new switch was installed in reverse order to the steps indicated above (two screws behind knob, 5 wire-crimped fasteners, 4 screws to panel). Range was pushed back into position and breaker turned on.
Read less
Was this helpful?
Thank you for voting!
Bake element brokeand caught fire
2 of 3 people
found this instruction helpful.
-
Lillian from coral springs, FL
- Really Easy
- Less than 15 mins
-
Nutdriver
Ordered the bake element part from partselect.com. When the part arrived I removed the 2 6mm screws from the element, I used two clips to hold the wires in place so that they didn't receed back into the stove. I installed the bake element, installed the two scews ans was done. It took all of 10minutes.
Lily in Florida
Lily in Florida
Was this helpful?
Thank you for voting!
The storage drawer came without supports.
2 of 4 people
found this instruction helpful.
-
Dock from Aurora, CO
- Really Easy
- Less than 15 mins
-
Nutdriver
I just removed the drawer and installed the rear supports as instructed on paper included with the part.
Was this helpful?
Thank you for voting!
Lower bake element burned out
1 person
found this instruction helpful.
-
Belinda from Rockford, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
I didn't know anything about this repair, other than I was replacing a part, so it never occurred to me that I needed to make sure there was no power to the oven. When I pulled the element out, there was a large spark. I flipped the breaker off, then finished the R&R.
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Make sure you turn power off at the breaker, then replace ... Read more the element.
Tim
Read less
Was this helpful?
Thank you for voting!
Element blew hole in self then no power to burner.
2 of 4 people
found this instruction helpful.
-
Melvin from Portland, TN
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
Replaced burned element, did not fix no power problem. Ordered receptor replacement, replaced it, took less than 10 mminutes, but still no power to burned. Then ordered replacement switch, replacement too less than 10 minutes again and burner works fine.
Was this helpful?
Thank you for voting!
The heating element broke in half.
1 person
found this instruction helpful.
-
Paul from Louisville, KY
- Easy
- Less than 15 mins
-
Screw drivers, Socket set
This was a very simple procedure. I removed the 2 screws in the oven itself (holding the element in place), then pushed the element through the back of the oven so the wires were exposed, then slipped off the wires, the male end from the female end, I then removed the entire element. I put the new element in the over, re-attached the wire
... Read more
s, put the screws back in place, replaced the cover, and the oven was as good as new.
Read less
Was this helpful?
Thank you for voting!
Bake element was burnt out.
1 person
found this instruction helpful.
-
Bertram from ABERDEEN, MD
- Very Easy
- Less than 15 mins
-
Socket set
1.Disconnect the power cord. 2.Remove two screws pull the element out. 3.Disconnect the wires attach to element. 4. Install the new element connecting the wires. 5. Align element
... Read more
with holes and tighten screws. 6. Plug in power cord and begin to cook.
Read less
Was this helpful?
Thank you for voting!
Oven was very slow to heat
1 person
found this instruction helpful.
-
James from CANAL FULTON, OH
- Very Easy
- Less than 15 mins
-
Nutdriver
Removed the rear panel from the Range using the nut driver. pulled the terminal wires off the back of the heating element. Double checked if there was continuity across the heating element terminals before removing the element. If there is none, its bad. remove the two screws inside the oven holding the element in place. Once free, lift t
... Read more
he front of the element to about 30 degrees and pull towards you. Insert the new element in the reverse manner then secure it using the two screws. Push the terminal wires onto the terminals on the back of the element and reinstall the rear panel.
Read less
Was this helpful?
Thank you for voting!
Back element was broken
1 person
found this instruction helpful.
-
Shiirley from CASPER, WY
- Really Easy
- Less than 15 mins
-
Pliers
My son did it by using pliers. He took out the screws that held the element in and pulled it out and used the pliers to pull the wires out of the old one and snapped the new one in . put it back together. about 5 minutes.
Was this helpful?
Thank you for voting!
Not Reaching Temperature above 300 Degrees
1 person
found this instruction helpful.
-
Ron from SAN TAN VLY, AZ
- Very Easy
- Less than 15 mins
-
Nutdriver
Take off 6 screws of back cover of the range, unplug the white wire. Go to the inside of oven, pull out racks. At the top of the oven is your Broiler element, in the center you will see a rod sticking out with one screw holding it in place. Take out screw and pull temperature sensor out toward you. Reverse steps to put it back together.
Was this helpful?
Thank you for voting!
oven door gasket needed replaced
1 person
found this instruction helpful.
-
Mary from LONGS, SC
- Very Easy
- Less than 15 mins
Ordered the part, it arrived and 5 minutes later it a complete installation
Was this helpful?
Thank you for voting!