EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

JBS262F3 General Electric Range - Instructions

All Instructions for the JBS262F3
106 - 120 of 481

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Range element was intermittent - bad contact at wire
2 of 4 people found this instruction helpful.
  • Ron from Carrollton, TX
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Drilled out the screw on one wire as it was corroded to the metal socket. Sanded both wire terminations. Installed wires into terminal block. Reassembled all loose parts and installed into burner slot. Worked perfectly.
Was this helpful?
Thank you for voting!
Bottom element in oven caught on fire and broke in two
1 person found this instruction helpful.
  • SHERYL from VERO BEACH, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver
The element was 25 years old and I was concerned about changing it. But is was so easy. I turned off power and removed 2 screws and then unscrewed the wiring from the old element. I had the new one installed in minutes. I was so glad to have my oven working again. Who needs a man.
Was this helpful?
Thank you for voting!
boken element
1 person found this instruction helpful.
  • cynthia from snyder, NY
  • Really Easy
  • 15 - 30 mins
  • Wrench set
remove screws attaching burner plate to back of oven, pull out element, undo wiring to old burner by unscrewing 2 screws, remove old burner, reverse process to put new burner in
Was this helpful?
Thank you for voting!
Bottom element had burnt out.
1 person found this instruction helpful.
  • Robert from Harrisburg, PA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Unplugged stove, removed front door, carefully removed two screws holding the cover plate of the element. Gently pulled the element out about 3-4 inches removed the two screw attaching the electrical wires to the element , making sure the wires did not pull back into the stove. Removed old element, attached new element to the electrical wires with the new screws received with the new element. Carefully pushed the wires and element back into place making sure the insulation was also in place. Re-attached the cover plate with the two screws I had removed. Plugged the stove back in and tested the element. Replaced the front door .... job complete!

Just wanted to add that the part came in two days, super mailing time, thanks!!
Was this helpful?
Thank you for voting!
The oven heating element was broken
1 person found this instruction helpful.
  • Daniel from Denver, CO
  • Really Easy
  • 15 - 30 mins
  • Pliers
I removed the 2 screws and the 2 wires from the broken heating element. I removed the broken oven heating element. Then I attached the 2 wires to the new heating element and put the 2 screws in to attach the new heating element into the oven. The new oven heating element worked just fine and I was done.
Was this helpful?
Thank you for voting!
Element at the bottom of oven cracked
1 person found this instruction helpful.
  • AMELDA from BRYANS ROAD, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers
First I turned off the circuit breaker leading to the oven. Then I removed the two screws that held the old element in place. I pulled out the element and disconnected the wires. I reconnected the wires to the new element and pushed it back in place. I then secured it with the two screws. I turned the circuit breaker back on and turn ed on the oven. Works just great!!!
Was this helpful?
Thank you for voting!
Element either shorted or burned out.
1 person found this instruction helpful.
  • Patrick from Durham, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
Removed two socket head screws form inside oven rear wall. Pulled element out and disconnected two screws attaching wiring. Replaced with new.
Was this helpful?
Thank you for voting!
Bake element developed a hot spot that burned through it.
1 person found this instruction helpful.
  • Paul from Slatington, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Easily removed two screws, pulled the wires out of the oven wall, disconnected the old and reconnected the new, pushed it back into the insulation, inserted the screws and tightened them. There was a problem with the model number. It was on a vinyl plate inside the oven drawer wall. The plate was slightly yellowed so I used my fing er to wipe the yellow away. When I did, the model number ended up as a black smudge on my finger tip. GE's engineers could have come up with a better method of displaying the model number. GE's customer service operator, however, did an excellent job of helping me to ascertain, at least, some of the number.
Was this helpful?
Thank you for voting!
Knob/switch would not turn right front burner on at all!
3 of 7 people found this instruction helpful.
  • William from West Liberty, KY
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enoug h slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!
Was this helpful?
Thank you for voting!
Bake element burned out in oven
1 person found this instruction helpful.
  • AL from GENOA, NE
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First shut off power to the range in the electrical
breaker box (its the 220 breaker) as marked.
Remove the oven door ( open part way and lift up) the
door will come off.
Remove the 2 screws that the element is attached to the
back of the oven wall. Pull element out part way and
disconnect the 2 wires. Take out element.
The new element had different connections so I cut off
the clips stripped the wires and attached to the element
connection . The element had connections that this was
possible. Push wires back into oven wall and install the
new element with the 2 screws that were removed. You
could also put on clips to the 2 wires that attach to the
element if so desired. (Eye hole clips.)
Was this helpful?
Thank you for voting!
The small element blew out consequently shorting out the infinite switch.
3 of 7 people found this instruction helpful.
  • Susan from Bend, OR
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for m y husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person found this instruction helpful.
  • Doug from Sewickley, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is stil l a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Was this helpful?
Thank you for voting!
Oven lower Bake Element exploded
1 person found this instruction helpful.
  • Fred from Renton, WA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
First observed the situation to determine if I should try and repair. I decided I could and should. Got the element and proceeded. I first turned the power off at the circuit breaker to cut the electrical power to the stove then I removed the two screws that holds the unit in place and then pulled unit out to where I could see the wire co nnection; removed the two screws on the wire connection and replaced the old element with the new element. reinserted the unit back into position and replaced the two screws that holds the unit in the stove. Turned power back on and tested the oven for any problems. Stove is working great.
Was this helpful?
Thank you for voting!
Oven heating element failed
1 person found this instruction helpful.
  • megrew, from COLORADO SPGS, CO
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Identify oven breaker and turn off power before starting. Opened oven door. Removed oven racks. Use 1/4" socket or nut driver to remove the 2 bolts holding heating element mounting bracket at rear base of oven. Carefully pull element out of installation mount to remove the 2 machine screws that attach electrical wires to the heating eleme nt. Reattach wires in same order as original element. Then reinstall new element in reverse order of removal. Took all of maybe 15 minutes! Excellent OEM Parts!
Was this helpful?
Thank you for voting!
Element burned out
1 person found this instruction helpful.
  • Wendy from CHESHIRE, CT
  • Really Easy
  • 15 - 30 mins
  • Socket set
My husband first turned the main breaker off to the stove. Pulled the stove away from wall, took off the back plate, unhooked the element and out the new one in!!
Was this helpful?
Thank you for voting!
All Instructions for the JBS262F3
106 - 120 of 481