JBS07V2 General Electric Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bake element burned out
1 person
found this instruction helpful.
-
Lavona from JACKSONVILLE, FL
- Very Easy
- Less than 15 mins
-
Screw drivers, Socket set
Flip the circuit breaker going to oven off, then used a 1/4 inch socket on the mounting flange bolts and the bolt head screws attaching the wires. Then used a flat head screwdriver to reattach the wires with the supplied screws and bolted the new element in place. Back to the circuit breaker flipped the switch and turned the oven on to te
... Read more
st it, and now works fine. *be sure to remove the sticker before installation, use rubbing alcohol to remove any residue.*
Read less
Was this helpful?
Thank you for voting!
broken heating element
1 person
found this instruction helpful.
-
Sherry from BLUFFTON, SC
- Very Easy
- Less than 15 mins
remove broken heating element and install the new one
Was this helpful?
Thank you for voting!
Bottom oven heating element was out
1 person
found this instruction helpful.
-
John from FALL RIVER, MA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Very easy repair. 2 hex head screws to take the heating element out. Then 2 more slot head screws for the wire connections. Perfect fit and operation of the new heating element.
Was this helpful?
Thank you for voting!
Shorted out the burner... fat gets into the receptors on these old stoves.
1 person
found this instruction helpful.
-
Todd from Mountain View, CA
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
The only hard part about putting in a new terminal block (and this time I had to replace the burner too, because that fried too) is stripping the stove wires, because that thermal insulation is very hard to get off. Otherwise, it's simple. In this case, I had already replaced this one (sigh), so had already cut & stripped the wires, so
... Read more
it was all easy. Frankly, the sane thing to do is buy a new stove, but wife is too cheap.
Read less
Was this helpful?
Thank you for voting!
Heating Element Was No Longer Working.
1 person
found this instruction helpful.
-
Karen from Stuart, FL
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
Removed oven door by holding sides and pulling upward. It's easy to remove and replace. Removed shelves by sliding back and up, then out. Removed two hex nuts with socket wrench. They are on back wall of oven and secure element to that wall. I then pulled element out about 3 inches and disconnected the two leads.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
I put new ... Read more element in, reconnected two leads, replace two hex nuts and was done.
Turn off power to stove at circuit breaker before starting.
Read less
Was this helpful?
Thank you for voting!
bake element burnt out
1 person
found this instruction helpful.
-
MIKE from CHATHAM, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
super easy - unpluged stove - unscrewed old element w/nutdriver from back of stove. unwired element - discarded. wired new element (2 wires). secured new element to back of stove. pluged stove back in. works great. Ordered part on Sunday, recieved it on Tuesday- VERY NICE SERVICE
Was this helpful?
Thank you for voting!
elemant had burnt into
1 person
found this instruction helpful.
-
Tracy from Paris, IL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, then i connect the new element and and replaced the screwes that held it in very simple and I must say Part select was very fast at getting me the correct part the first time , they have earned
... Read more
a spot in my Favorite list
Read less
Was this helpful?
Thank you for voting!
Oven wouldn't heat
1 person
found this instruction helpful.
-
Doug from Sewickley, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
Couldn't be a much simpler repair. You pull the old element off by removing two screws. Then you slide the old element toward you several inches and remove the two screws holding the wires that are attached to the old element. To replace, just do everything in reverse. One cautionary measure, even though the oven is off, there is stil
... Read more
l a small amount of electricity going to the element. Turn the stove off at the circuit breaker, or unplug the stove before you attempt the repair.
Read less
Was this helpful?
Thank you for voting!
Element was cut
1 person
found this instruction helpful.
-
Rosaire from St. Agatha,, ME
- Really Easy
- Less than 15 mins
-
Nutdriver
Removed two screws and take Element out and put new one in.It is very easy to do.
Was this helpful?
Thank you for voting!
the burner trays just needed replaced for an 85 year old senior citizen
1 person
found this instruction helpful.
-
Bet from Bothell, WA
- Easy
- Less than 15 mins
Removed burner trays, pulled out heater unit, cleaned up inside of area around all four burners, slipped the burner trays back in and pushed the heater unit back into place.
Other Parts Used:
Was this helpful?
Thank you for voting!
Oven element melted then naturally would not heat.
1 person
found this instruction helpful.
-
Rex from Colton, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I removed the old element from the oven and replaced it with the new element. Then I connected the two wires to the new element and pushed the element into place. Then I replaced the two scre
... Read more
ws that held the element in place. I then tested the oven and it worked wonderfully.
Read less
Was this helpful?
Thank you for voting!
Something Had Dripped Down On The Baking Element Causing It To Over Heat In One Spot And Short Out.
1 person
found this instruction helpful.
-
JAMES from LEBANON, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. A
... Read more
lthough not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.
Read less
Was this helpful?
Thank you for voting!
The heating element in the oven failed, after at least 16 years of good service.
1 person
found this instruction helpful.
-
Nancy from Golden, CO
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Tur
... Read more
ned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!
Read less
Was this helpful?
Thank you for voting!
Burner worked intermittently
1 person
found this instruction helpful.
-
Mike from Rowlett, TX
- Really Easy
- Less than 15 mins
Lined up the prongs and slid it right in, took 30 seconds.
Was this helpful?
Thank you for voting!
element wont heat up
1 person
found this instruction helpful.
-
Mr Sal from Eastampton, NJ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
4 screws 4 off then 4 on done
Was this helpful?
Thank you for voting!