EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

J797D2 General Electric Range - Instructions

All Instructions for the J797D2
76 - 90 of 118

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burnt out broiler element in oven
  • Ronald from Silver Spring, MD
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers, Socket set
Broiler element failed catastrophically (with light flashes) while in use (1986 GE self-clean oven/four burner stovetop). Part number embossed on element plate - very difficult to see - took digital photo while still in oven and magnified. Easy to search for part. Good price, prompt delivery. Removal of old and install new awkward bec ause of access angle and my decreasing nimbleness, as well as oven control thermocouple and support bracket in way. But no technical difficulties. Hex head metal screws holding in element; Notched phillips metal screws holding bracing bracket (easier to put element in by removing one side of bracket). Screws difficult to remove as in much used oven 26 years, and thermocouple partially blocking socket ratchet wrench. Would have been easier with 1/4" short extension. Before detaching element, I used twist ties around the leads tied to a large plastic clip so as not to lose them into oven back. PartSelect part was made by GE, not secondary source. Perfect replacement for this old part - still available.
Was this helpful?
Thank you for voting!
Broiler element not working
  • Jone from Palmyra, VA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Some times it's not the element at all, as in this case. After rmoving the element I found the wires broke. Fortunatly I had some high temp wire left over from a earlier oven repair. I used butt splices and heat shrink tubing to repair the wires. Then I crimped on a couple of eyelets and fastened things dow.n I received a big kiss form th e wife for getting the broiler fixed so fast. Maybe a little extra work, but the rewards were worth it.
Was this helpful?
Thank you for voting!
broil element failure
  • Glenn from Plano, TX
  • Really Easy
  • 1- 2 hours
  • Pliers
Unscrew 4 easy nuts and 1 most difficult nut, gently pull both long and short wires, at this point assure the wife that you did turn off the power.You may wish to attach a cord to short wire as it wants to vanish into the rear bowels of the oven On instruction of the wife clean the oven. Reverse dismantling procedure. Switch oven on. Bask in wives praise.
Was this helpful?
Thank you for voting!
Broiler element burned out
  • Glenn from Old Saybrook, CT
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Repair is pretty easy, its the accessability that makes it difficult. This is a wall mount oven. Removing the door would provide pretty good access, but having to reach over the door into the very top back of the oven is a real pain (in the back and other places). As another customer said, there were many dropped screws and much cussin g. The old element terminals were just holes in a metal tab that accepted tapered screws. The new element had terminals that were threaded to accept the screws provided. It took lots of twisting and turning of the element and the power wiring to get the terminal on the wire lined up with the terminal on the element in a position where I could hold them together and insert the screw and start the threads. Don't try this after you've had a beer or two. Whew!!! Many tries, sore back, but did it. Like I said, simple except for the reach. Bake element was much easier. Hope I don't have to do this one again. My GE oven is a winner (20 plus years old) and Parts Select has what you need at a reasonable price and ships quickly. Have used before and will use again, if needed.
Was this helpful?
Thank you for voting!
Bad Burner
  • Grady` from Titus, AL
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
There was no burner listed like 40 yr old burner that failed. Got one the same size and connections. Cut old burner out of the stainless steel ring and new burner fit right in. New burner works great
Was this helpful?
Thank you for voting!
Original trim ring did not fit
  • Sarah from San Andreas, CA
  • Really Easy
  • Less than 15 mins
I had an appliance guy replace a burner(Calrod unit)on my 47 year-old GE range, but he didn't tell me that the original trim ring wouldn't fit. I decided to look up on PartSelect to see if I could get one to fit the new burner, and I did! Fits perfectly......no tools needed.
Was this helpful?
Thank you for voting!
dirty drip pans and rings in new house i bought
  • patricia from richland, WA
  • Really Easy
  • Less than 15 mins
could not find the proper pans and rings in any diy stores, as stove is so old. went on this site and there they were!!!
Was this helpful?
Thank you for voting!
I needed new Drip Pans
  • Gloria from San Jose, CA
  • Really Easy
  • Less than 15 mins
I purchased a set of drip pans at the store only to find out that they were not for GE Ranges. I got on line and inquired and your representative was very helpful. The repair was easy. After cleaning the stove I removed the old drip pans and installed them one by one. No problem!
Was this helpful?
Thank you for voting!
Condo Had Very Old Drop In. Threw Away Drip Pans And Rings
  • Valerie from Ogden, UT
  • Really Easy
  • Less than 15 mins
Placed new ones on range. Exactly what I would do to wash them.
Was this helpful?
Thank you for voting!
Broiler Element Burned Out
  • Robert from Mission Viejo, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers, Wrench set
The repair was very eash. The replacement element fit perfectly and only involved removing two screws, pulling the old element out far enought from the bak of the oven to disconnect the wires held by two screws . Disconnecting the two wires and installing the new element. This is a 25 year old appliance and is back to working like new. One note, be sure to shut the power off to the range because one of the wires connected to the element remains HOT! even if the oven is not on.
Was this helpful?
Thank you for voting!
Threw away old parts!
  • Valerie from Ogden, UT
  • Really Easy
  • Less than 15 mins
Put bowl in and then slid rings around. Just like cleaning procedure. Easy. Thanks for your service.
Was this helpful?
Thank you for voting!
heating element burned out.
  • Joseph from Bremond, TX
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
Replaced 30 year old stovetop cooking element with no problems. Stovetop works great now.
Was this helpful?
Thank you for voting!
dirty drip pans and rim trims
  • Anna from Las Vegas, NV
  • Really Easy
  • Less than 15 mins
Threw away the old ones after lifting burner rings. Put new parts in place.
Was this helpful?
Thank you for voting!
old stained drip bowls
  • Peter J from Oceanside, CA
  • Really Easy
  • Less than 15 mins
I tried first to replace them, with a set I bought at a local hardware store. But they were too small. So I went on the internet, and found Part Select, and thanks to a very helpful guy, who made the extra effort to find the exact drip bowls, I now have a nice, shiny stove-top again. Installing them took two minutes... tilt the burners u p, and slide them in. No problem.
Was this helpful?
Thank you for voting!
Old drip pans rusted out.
  • Joseph from San Antonio, TX
  • A Bit Difficult
  • Less than 15 mins
Range is 45 yrs old. New drip pans are different shape. This is only place which had them and VERY GOOD price. Delivery was quick, too!
Was this helpful?
Thank you for voting!
All Instructions for the J797D2
76 - 90 of 118