IFW7300WW02 Inglis Washer - Instructions

Removed bottom panel, removed hoses and pump. Reinstalled in reverse order.

I pulled the washer away from the wall to comfortably access the back panel. I then removed about a dozen 1/4 drive screws. I had to remove all the screws in the panel and the screws and cross brace directly behind the drum in order to install the new belt. Note: it will seem like the belt is too small when in reality it is perfect. There ... Read more is no type of adjustments or tensioners that I found so you need to place the belt on the motor pulley correctly and then walk the belt on the drum pulley. Make sure the belt is lined up with the marks on the drum pulley that the original belt had left. You may need to attempt to walk the belt on 2 or 3 times before it finally goes on. If you have any mechanical knowledge you will find this to be a gravy job.

Overall, the install was easy.
Just a matter of getting yourself to get it done.
The video on the removal / install procedures was most helpful.
The front shocks were completed very quickly. The rear shock required all hoses to be disconnected and the back of the washer to be removed. After removing perhaps a dozen screws t ... Read more he cover was still fastened. You will see (in my case) 4 plastic flat clips. after they were removed the back came off. The rest of the project was the same as the front shocks. 1st time thru so to be expected.
Anyway, certainly a project that any DIYer can tackle.
Thanks Partselect for the correct parts in a timely fashion and the knowledge to perform the install.
Scott

My washer is part of a washer/dryer stack and i did not remove the dryer for the repair. I followed a YouTube video that shows the basics of how to do this repair:
1. Remove the spring-compressed outer band. Did this with needle nose pliers. Then removed the bellows from the outside of the frame--really easy.
2. Remove th ... Read more e inner band. Used a stubby philips head screwdriver while pushing the tub inward to get more room.It was awkward, but patience is key. Once that was loose i removed the inner ring then the bellows from the tub.
Total time for removal was maybe 30 min

For the install i took my time and started at the bottom of the tub and pressed the new bellows in the groove making sure it was in properly. Then the ring went on and again, take the time to make sure it's in the groove. Then tighten.
Lastly attache the bellows the the frame of the machine making sure to take your time to properly seat it in the groove.
The most challenging part was getting the outer ring back on. expanding the spring is a challenge. I used just needle-nose pliers to expand it while trying to keep it from slipping off. I believe there is a tool to expand the ring and it's probably worth buying it to make this step easier.
Over all the install took maybe 30-40 min.
Happy i got it fixed. Good luck!

Removed the old pump and installed the new one. Most difficulty came from the fact that the dryer is on top of the washer and the washer is inside a plastic pan that has a 2 inch lip which made it difficult to remover the front panel.

unhooked two water lines & electrical plugin unbolted old pump and installed new pump. took about 15 minutes.

I followed the instructions in the video (available on the site) and had no problem whatsoever to replace the boot. This video is so detailed that it is difficult to go wrong.
Only caution I would make is that this may prove to be a bit too much if the person has never ever used tools before.

Unplug machine from electrical outlet.
All screws can be removed with a 1/4" socket, either with a socket wrench or nut driver.
Top panel - remove three screws on back, slide panel back an inch or so, and lift off.
The control panel must be carefully pulled off by using a screwdriver to pry it away, and then placed on top ... Read more of machine. Be careful not to disconnect or damage any attached wires.
Pull out the detergent dispense drawer, press the retainer on the left rear of dispenser drawer, and pull it out and set it aside. One small torx screw must removed from the dispenser housing.
Bottom front panel - remove three screws to take it off. This exposes the screws on the front panel.
The front panel of machine must be removed as well.
This is the most tedious part of the job, as the door seal must be disconnected from the panel. Remove the wire and spring retainer around the door that holds seal in place. The spring portion of the retainer is on the bottom of the opening. Pry it off with a screwdriver, being careful not to damage the rubber seal. Do not remove it, simply push it into the washer opening.
Remove the screws from the front panel - two on top, and two bottom. It has some wires on the right side, and to avoid damaging them, support the panel with a stool and prop it up against the machine.
You can now access the hose on the rear bottom of the dispenser. Using a pliers, squeeze the retainer and pull the hose off the dispense. The other end is pressed into the tub - simply pull it out. I recommend cleaning the edges of hole to assure a good seal when installing the replacement.
To install the replacement hose, press it into the tub, making sure to get the channel in the hose properly inserted in order to make a solid seal. Attach the other end to the dispenser with the retainer.
Reassemble by reversing the order described above.

Unhooked two hose clamps took two screws off put new aprt on hooked back up works great

removed bottom panel and took out pump and replaced it with new one

ordered another baffle 5 minutes to install 40 dollars to order .and I saved my self 80 dollars service fee plus parts and laborer.

My husband removed the bottom panel of the washer and removed the old pump with two screws, then removed the water hose coming into the pump and unplugged the electrical push in type plug from the side of the pump. Simple reversed the process to instal the new one and replaced the front panel. Simple really...far more so than calling a re ... Read more pair man.

Remove two star screws. Remove broken striker. Installed new striker. Took two mins.

My husband and son removed the old pump and replaced it with the new pump assembly. The whole process took about 30 minutes max.

The washing machine would only run on the hot water cycle. When trying to use the warm or cold setting, the water would dribble into the drum and result in an LF error code(long fill). I watched a brief video on replacing the water inlet valve which made it really easy to repair. I first turned off the water, disconnected the hoses from t ... Read more he machine, and opened the top to access the valves. I then disconnected the wires from the valve, removed the water tubes, swapped out the valves and put everything back together. I am not experienced in repair but this was a very easy fix! We decided to replace the single hot water valve and the dual cold water valve since it's an older machine and it works like new again!