- Home
- GLGFS86DQC
- Instructions
GLGFS86DQC Frigidaire Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven igniter not working
2 of 2 people
found this instruction helpful.
-
Raymond from Eustis, FL
- Really Easy
- Less than 15 mins
-
Socket set
Having already removed the old igniter , replaced it with new.
Was this helpful?
Thank you for voting!
bottom oven plate had foil stuck to it
4 of 9 people
found this instruction helpful.
-
Wilma from Syracuse, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
Very easy to order,part was delivered promptly and installation was easy.I unscrewed a few screws and lifted the bottom panel out and put the new one in.
Was this helpful?
Thank you for voting!
lens was broken
2 of 3 people
found this instruction helpful.
-
Kenneth from Coeur d'Alene, ID
- Really Easy
- Less than 15 mins
after pulling away from wall and unplugging remove 5 screws in upper back panel lift off being careful of sharp edges if part of lens is still in hole push it out towards the front insert lens from front of unit slide light assy over pin on back of lens replace back panel plug in range push back against wall check for level you're done
Was this helpful?
Thank you for voting!
weak oven igniter/not enough amp. to light oven
3 of 6 people
found this instruction helpful.
-
JEFFREY from ULSTER, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver
first I removed oven draw for access, then removed the two screws with a nut driver, next removed the two wire nuts and the old element was free. Replaced new element in reverse steps of removing old and the new part ignited the stove within 30 seconds, but now I have no excuse for not fixing dinner!! Thanks for promt shipping, it arri
... Read more
ved early than anticipated.
Read less
Was this helpful?
Thank you for voting!
Gas stove won’t light on half the appliance
4 of 9 people
found this instruction helpful.
-
Julieta from ELMIRA, NY
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set
First we replaced the wiring harness because a multi-meter said it wasn’t getting power. That was only partially true. The wiring harness was burned looking so we just kept it instead of sending it back. When the spark module got here the burner caps were removed and then the wires were noted where they went on the module and then the pow
... Read more
er and gas were turned off. The spark module was removed and then the stove was tested and we were back in business.
Read less
Was this helpful?
Thank you for voting!
This is stove and convection oven Baker igniter
2 of 3 people
found this instruction helpful.
-
james from CROSBY, TX
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
Had to pull back off due plug in for bake Ignitor is on bottom right Conner , mfg ill design , part was is to install after that. Parts select is great to deal with first part showed up damage due to shipping , parts select sent another with better packaging , works great have used them in the past for Ref ice maker parts . Due it yoursel
... Read more
f save money
Read less
Was this helpful?
Thank you for voting!
Took a long time to light oven, smell of gas, slow heat up.
2 of 3 people
found this instruction helpful.
-
Todd from OLYMPIA, WA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Really easy to do, did not have to bring stove out from the wall! Turn power off to the stove. Remove the lower drawer. Remove the oven rakes. With a slotted screwdriver remove two screws in back of bottom oven cover, use 1/4 inch socket to remove two screws in front. Remove bottom oven cover. You can then see the part to be removed whi
... Read more
ch has two wires going into it, the unit looks identical to the new part which heats up and lights the gas grill for the oven. I cut the two wires from the old part, remember which is the upper and lower; remove two screws holding onto part. Wire new part remembering top and bottom. Push extra wire down into bottom drawer and then mount new part with two screws. Turn power back on and try oven. Lite right away for me so I knew I had replaced the bad part. Reassemble and Enjoy!!
Read less
Was this helpful?
Thank you for voting!
Longer time for oven to preheat. Replacing oven igniter solved my issue
1 person
found this instruction helpful.
-
Winfred from CARSON, CA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
First thing is I looked for videos on how to replace oven igniter to get an idea. Unplug AC cord and turn off gas valve.On my model I was not able to figure out how to remove oven door. You can still work around it without removing. Inside the oven, remove bottom cover. Remove 2 screws located in rear corners. After removing oven bottom c
... Read more
over, next is a burner cover. Remove 2 screws located toward front of oven using a nutdriver or socket. After removing burner cover , you will find oven igniter. Now remove bottom drawer. This is why its a bit difficult for others. Igniter has 2 leads. Laying down on the floor and reaching in to follow-identify where the 2 leads go to. Using same nutdriver or socket remove 2 screws that hold up the igniter. I cut the leads from the base of the old igniter so you will have some slack to work on when you reconnect the wires underneath. Install new igniter, run leads same way.Strip back about 3/8 in. wire, twist leads to proper wires and twist on ceramic wire cap that is provided. Make sure no bare wires are exposed! Now you can test.
Read less
Was this helpful?
Thank you for voting!
Oven glows but won't ignite
1 person
found this instruction helpful.
-
John from MANASSAS, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Thank you, Thank you and thank you!!! I couldn't be happier and I save over $200 in repair. My repair was very easy after watching the video. I cut off the wire and ensure that the new one are attached into place. Placed all parts back and boom, the oven starts working a new.
Was this helpful?
Thank you for voting!
Oven wouldn't light
1 person
found this instruction helpful.
-
JERRY L from PIPER CITY, IL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed oven door, removed oven floor. Unscrewed skirt with attached igniter and gas tube. Two nut screws hold igniter to burner. Remove old igniter and replace with new, reattach two wires with supplied wire nuts. Replace oven floor and door. Oven lit right up, pizza anyone?
Was this helpful?
Thank you for voting!
igniter burned-out, not able to start oven
1 person
found this instruction helpful.
-
BETTY from PHILADELPHIA, PA
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
followed directions enclosed.required removal of oven door and old igniter
Was this helpful?
Thank you for voting!
would not light
1 person
found this instruction helpful.
-
clayton from rockford, IL
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
open oven door remove bottom of oven then remome the metal cover over the burner to expose the ignighter remove 2 screws that hold it to the bracket. the two wire's that come out of the ignighter run down under the bottom oven pan, i removed the bottom front cover by lifting up and then pulled out, then i could see the wires i removed the
... Read more
wire nuts and pulled old wires off and removed old ignighter. i pulled off the insulator covers from the old one and slid them on the wires of the new ignighter then i fished the wires back down and and attachted them with the wire nuts, then reasembled the rest of the oven. woks great!
Read less
Was this helpful?
Thank you for voting!
Oven of gas range not igniting
1 person
found this instruction helpful.
-
Hubert from Street, MD
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed lower drawer of oven and base panel of oven. Unplugged stove from outlet. Removed old igniter w/ nut driver (two screws). Disconnected wires (blade connectors) from stove base. Disconnected two-pole plug from oven after removing protective cover in corner.
Install new igniter. You will need to cut existing wires fro ... Read more m old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.
Install new igniter. You will need to cut existing wires fro ... Read more m old igniter so that spade and two-pole connectors can be reused. Join these wires with the new ignitor wires using the ceramic wire nuts provided with the new unit.
Directions are also provided with the new igniter.
Read less
Was this helpful?
Thank you for voting!
. F3 error code
1 person
found this instruction helpful.
-
Garry from New Haven, CT
- Really Easy
- 30 - 60 mins
-
Nutdriver
I was getting an error code every time I turned my oven on. After a Google search I discovered it was a faulty oven temperature sensor. This website is awesome because it has a video showing how to install
Was this helpful?
Thank you for voting!
GAS OVEN WON'T LIGHT.
1 person
found this instruction helpful.
-
stephen from LIVERPOOL, NY
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
AS YOU DESCRIBED IN YOUR YOU-TUBE VIDEO, THE OVEN IGNITER WOULD GLOW BUT THE OVEN WOULD NOT LIGHT. YOU EXPLAINED THAT THE PROBLEM COULD STILL BE THE IGNITER AND SO I ORDERED A NEW IGNITER AND THEN WATCHED YOUR VIDEO ON HOW TO ACCESS AND REPLACE THE NEW IGNITER AND THAT FIXED THE PROBLEM. I ONLY HAD TO CUT THE OLD WIRES ON THE OLD IGNITER
... Read more
AND MATCH WIRES WITH THE NEW IGNITER USING THE CERAMIC WIRE NUTS SUPPLIED, AND I WAS BACK COOKING AGIN. THANKS.
Read less
Was this helpful?
Thank you for voting!