EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLER341AS2 Frigidaire Dryer - Instructions

All Instructions for the GLER341AS2
121 - 135 of 568

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
No Heat, Dryer Runs, But Right Side Of Timer Would Not Advance, Left Timer Would
2 of 2 people found this instruction helpful.
  • STEPHEN from Nashville, TN
  • Easy
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
I used the percentage scale on this website to try and determine the likely cause. After reading several sites, I couldn't make sense of the timer not working on just one type cycle. When I got the dryer drum off, I could plainly see that one of the heater coils was broken. They get heat stressed and break down over time and a hard shak e probably finished this off. This unit is 5 plus years old. It was Saturday and I had no heater, so I actually found it at a local parts supplier. Also replaced the drum bearing and the bearing cup in the rear along with the heater. BTW, a new heater comes with a HIGH thermal switch attached to it so don't buy it extra. The bearing cone also comes with a new bushing in the pack. I DID use the Thermal Limiter that I order from the site because I was already in there. Everything works great now. I may have gotten most off my parts elsewhere but this site was the biggest help of them all. I will definitely be back here again.
Was this helpful?
Thank you for voting!
Loud Squealing
2 of 2 people found this instruction helpful.
  • William from Hudson Falls, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Remove top panel with large flat screwdriver and 2 screws in back.Remove bottom panel with 2 screws.Release belt tensioner and remove belt.Remove 3 screws in center of drum inside.Remove drum. Remove rear bearing by pulling up on assembly.Replace all parts in reverse order.
Was this helpful?
Thank you for voting!
replaced broken belt
2 of 2 people found this instruction helpful.
  • Shelia from Elizabethtown, IL
  • Easy
  • 30 - 60 mins
  • Wrench set
Romoved front from dryer . Then loosened tub , slid belt on , reached in back and put belt on pulley , turned tub till belt went into place and reassembled dryer all with the help of a 3 year old and an8 year old,so in my oppinion it was one of the easiest fixes i've ever done!
Was this helpful?
Thank you for voting!
Lound noise inside dryer
3 of 5 people found this instruction helpful.
  • Joseph from little Egg Harbour, NJ
  • Easy
  • 1- 2 hours
  • Screw drivers
1. unplug the dryer, remove the aluminum vent and move it to an area that has a lot of elbow room.
2. remove the top lid with a flat screwdriver. It seems that the top lid was being held by 2 metal clips on each end.
3. on the right hand side removed the 2 wires from the front face of the dryer. this is the switch for the open door sensor. remember which wire goes where.
4. the on the left and right side will be one screw and one metal clip, unscrew and pop the front panel with a flat screwdriver.
5. in front of the drum remove the plastic clip that is used as a guide for the drum to be in place.
6. look in the drum and there is 3 screws that form a triangle shape. remove the screws.
7. remove the belt from the drum. inspect the belt. replace if necessary.
8. lift up and pull out the drum.
9. remove the rear drum assembly and replace it with the new parts.
10. repeat in reverse and your done.
It took me 40 minutes the first time i replaced the rear drum assembly then i forgot to hook the belt up correctly and i unassemble the unit in 5 minutes fix the belt and assemble the unit in 5 more minutes. Now the wife is happy.
Was this helpful?
Thank you for voting!
Very noisy
2 of 2 people found this instruction helpful.
  • Cherry from WATERVLIET, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Replaced rear drum bearing, drum support bearing & drum belt. Still very noisy. Will order new motor & see if that does the trick.
Was this helpful?
Thank you for voting!
Broken Timer Knob, Broken Start Knob, Possibly Damaged Start Switch
2 of 2 people found this instruction helpful.
  • JEREMY from JONESBORO, GA
  • A Bit Difficult
  • 15 - 30 mins
  • Screw drivers
First, removed the metal access panel by removing screws. (EASY)
Second, pressed the timer knob onto the timer shaft. (EASY)
Third, mounted the start switch to the mounting surface. (A BIT DIFFICULT)

Fourth, pressed the start knob onto the freshly mounted start switch. (EASY)

Fifth, replaced the metal acces s panel by replacing screws. (EASY)

Dryer now functions like new.
Was this helpful?
Thank you for voting!
May not have to take out the whole drum to replace the limiter!
2 of 2 people found this instruction helpful.
  • Timothy from CRANBURY, NJ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After lifting the dryer top and finding the location of the thermal limiter on the back of the dryer, where it is difficult to get at, I carefully cut through the dryer cabinet with the multimaster on three sides to form a 'flap' upon which the limiter was mounted. By prying this flap open from the back, the two wires and two screws are e asily accessible to replace the limiter, without having to remove the whole drum. Afterwards, I just bent the flap back into place and taped the seams. If it ever blows again, the fix will take all of about two minutes.
Was this helpful?
Thank you for voting!
Dryer not heating
2 of 2 people found this instruction helpful.
  • Steve from COVINGTON, KY
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
UNPLUG DRYER (this is key) Removed the top of dryer. used screwdriver and pliers to remove two screws and electrical connections then reinstalled new part stick the magnet behind the part to the back of the dryer to help control the small screws.
Was this helpful?
Thank you for voting!
dryer wouldn't heat
3 of 5 people found this instruction helpful.
  • billy from millsboro, DE
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
remove top of dryer by prying with large screwdriver to snap back clips that hold it on remove two screws on both sides that hold the door . remove door then remove belt from dryer tub. (to remove belt take the back panel near floor off with screwdriver and lift pullie up that hold belt. )then lift tub upward to disconnect it from it's se at; pull it straight forward to get to the heating element.un bolt it with screwdriver and disconnect the sensor and put new heat element in
Was this helpful?
Thank you for voting!
2 of the dryers knobs had broken off
3 of 5 people found this instruction helpful.
  • Ann from Inglis, FL
  • Really Easy
  • Less than 15 mins
I ordered the knobs at less than half the price I paid before from the retailer. The knobs came in the mail very quickly. I took the knobs from the package and put them on. Easy repair, and I was especially happy with the ease of ordering and quick delivery.
Was this helpful?
Thank you for voting!
Dryer would not turn on, no power. Since i already have replaced thermal limiter switch, i knew exactly what to do and also how to shorten installation
2 of 2 people found this instruction helpful.
  • Daniel from SAN ANTONIO, TX
  • Very Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Remove 2 screws from back of unit, remove top by lifting and pulling up, set aside. Using pliers,needle-nose, remove the 2 wires from switch, then using a magitized philips screw driver, remove 2 screws holding switch to back of unit, replace switch, reassemble everything. 20 minutes, boom, ur done, dry some clothes now
Was this helpful?
Thank you for voting!
It got lost...
2 of 2 people found this instruction helpful.
  • Kevin from Rome, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
It was very, very simple... I just had to find two screws ( that were not included)...no problem...
Was this helpful?
Thank you for voting!
Door handle broke and came off.
2 of 2 people found this instruction helpful.
  • Elizabeth from Mentor, OH
  • Really Easy
  • Less than 15 mins
Simply popped it back into place, careful not to break the new handle.
Was this helpful?
Thank you for voting!
replaced knob, perfect fit and match
2 of 2 people found this instruction helpful.
  • Paul from Beverly Hills, FL
  • Really Easy
  • Less than 15 mins
just pushed new knob on.
Was this helpful?
Thank you for voting!
old knob was strip
2 of 2 people found this instruction helpful.
  • DENISE K from cleveland, OH
  • Really Easy
  • Less than 15 mins
remove old knob and washer that was on it put new knob on and turn the knob dryer was save
Was this helpful?
Thank you for voting!
All Instructions for the GLER341AS2
121 - 135 of 568