EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

GLEFM397DBA Frigidaire Range - Instructions

All Instructions for the GLEFM397DBA
76 - 90 of 110

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
really bad ugly streaks inside of glass
  • John from Hemet, CA
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
open door,throw the door latches at the hinges and remove door. Take the out of the outer panel so you can separate the glasses. remove clip that hold the outer glass in place. I ordered a replacement glass as I never thought that it would come clean it looked so bad, but it cleaned up like new so I now have a spare glass for my oven door . Just reverse the way you take it apart to put it back together.
Was this helpful?
Thank you for voting!
Oven door would not close all the way
  • Pat from Jacksonville, NC
  • Easy
  • 15 - 30 mins
  • Screw drivers
We orderes the hinge kit and replaced the bent hinges. The directions were easy to use (pictures really helped). The only issue was trying to remember where the screws went after we took it apart. Just a few moments of back tracking. Keep in mind we were working by flashlight. lol
Was this helpful?
Thank you for voting!
oven was too hot code f-10 came up
  • Donnie from McLaughlin, SD
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Pulled out range, unplugged power used nut driver to remove back and removed oven probe. Had to change end and reinstalled in reverse order.
Was this helpful?
Thank you for voting!
Needed to install an anti-tip bracket on my stove.
  • Daniel from Provo, UT
  • Really Easy
  • Less than 15 mins
  • Socket set
Moved the stove. Used the template to position the bracket. Put the supplied screws to attach bracket to the floor. Slid stove back into place. DONE!
Was this helpful?
Thank you for voting!
Bake element flashed and left a hole in element. Element was red to blowout point.
  • Lamont from Columbia, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed power plug from outlet. Removed metal racks. Used 1/4" nut driver to remove screws. Carefully pulled element straight foreword. After wires were exposed they were carefully removed. Made sure wires stayed outside mounting hole. Put new element in made sure wires were secured to new element. Carefully push back on element to get wi res in place. Put screws in element. Start one screw then the other. Then tighten both screws. Plug power cord back into wall" or turn circuit breaker on if you used that option. Turn dial to bake element on and check for prerogative operation.
Was this helpful?
Thank you for voting!
Bake element broke off near connector
  • Rose from Crowley, LA
  • Easy
  • Less than 15 mins
  • Nutdriver, Pliers
unscrewed brace attached to element without any problem and secured the wire so that it would not fall behind liner. Connector was a bit hard to disconnect so asked my handyman to detach it - I was not familiar with this connection and did not want to break it - he did it w/o problems and attached the new bake element pronto. How easy can it get!
Was this helpful?
Thank you for voting!
controler failure fault F7 40
  • William from Chrystal River, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
killed power removed back plate disconnected wiring removed old controller reversed this process.
Was this helpful?
Thank you for voting!
Cracked inner oven door
  • Steve from Hollypond, AL
  • Easy
  • More than 2 hours
  • Pliers, Screw drivers
Removed outer glass first ,then worked my way thru to inner glass..
Was this helpful?
Thank you for voting!
Oven turning off ater Pre- Heating
  • Catherine from Bowie, AZ
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver
Talked to someone who knows , DX'd the potential problem,looked for the part on your very user friendly website and your DX was exactly what my oven was doing, when the Thermo-Sensor arrived, I unplugged the oven, removed the metal back, took out the faulty Sensor, replaced it very easy then realized the plug was different, so called a fr iend who knows how to Solder and 2 hrs, later, my oven was repaired and I began baking an Apple pie to repay a friends kindness The pie was perfectly baked , my friend was happy and so am I ,the baker, just before the holidays Thank you Parts Select for helpful DX and speedy delivery - seems you saved Christmas for me.
Was this helpful?
Thank you for voting!
All Instructions for the GLEFM397DBA
76 - 90 of 110